background image

9

CLEANING YOUR 

POWER JUICER EXPRESS

• Turn off the power switch and wait until the motor completely stops.
• With dry hands, unplug the power cord from electrical outlet. 
• Disassemble the machine. (See disassembly instructions.)
• Clean all other parts in warm, soapy water. A mild detergent is recommended. Rinse well

and dry thoroughly. All components are dishwasher safe with the exception of the base. 
Do not use in European Import or a Commercial dishwasher.

• See instructions below for cleaning juice spout. 
• Wipe base with a soft damp cloth or sponge. Do not submerge base in water. 

Do not spray with water or any other liquid. Base is not dishwasher safe.

• To clean the filter/blade, hold under warm running water. Use a soft-bristled dish washing

brush gently to completely clean pulp from filter. Rinse the filter from the outside under 
running water.

• Dry components thoroughly then assemble the machine and turn the power on to spin out

any excess water.

• Make sure unit and parts are completely dry then store in a cool, dry place.
• We recommend removing juice spout after each use.

To Clean Juice Spout:

STEP 1: 

Locate removable juice spout locking mechanism on 
the bottom side of receptacle.

Note: Juice spout will be in the locked position.

STEP 2: 

To unlock, turn locking mechanism counter-clockwise,
lining up notch with juicer spout hinge pivot arm.

IMPORTANT:

When reattaching juice spout back into 

original position make sure juice spout is in the locked 
position and tightly secured before use.

STEP 3: 

Lift up juice spout carefully from receptacle 
and remove to clean.

To Reattach:

insert juice spout back into original 

position and turn the locking mechanism clockwise to 
lock into place.

Locking

Mechanism

Hinge 

Pivot Arm

LOCKED POSITION

UNLOCKED POSITION

Summary of Contents for Jack LaLanne's Power Juicer Express













Reviews: