I n s t a l l a t i o n , O p e r a t i o n , & M a i n t e n a n c e M a n u a l
3
www.trioniaq.com
ComfortBreeze
®
UV360-1 System
3. Application
The UV360’s unique “low-voltage” 24V power supply delivers
up to 22 Watts of UV-C power into most any application.
Its lamp and socket are water-resistant, and 24V power
means reduced danger from fire or shock. The UV360
installs simply from the exterior of HVAC equipment, no
need to access the systems interior. Simply create a 2-7/8”
insertion hole at the intended site, mount the fixture and plug
its UL Listed adapter into a nearby wall socket, or, wire it to
a suitable 24V power source (with no power fluctuations).
NOTE: THE UV360 IS RATED AT 22VA. IT IS
RECOMMENDED THAT THE ANTICIPATED 24V SOURCE BE
CHECKED FOR ITS ABILITY TO SERVICE A 22VA LOAD. A
SEPARATE TRANSFORMER IS RECOMMENDED.
4. Safety Considerations
Improper installation, adjustment, alteration, service,
maintenance, or use can cause fire, electrical shock, or other
conditions which may cause personal injury or property damage
and loss of warranty. Consult a qualified installer, service
agency, or your supplier for information or assistance. The
qualified installer or agency must use factory kits or accessories
when installing this product. Refer to the individual instructions
packaged with kits or accessories when installing them. Follow
all safety codes and wear safety glasses and work gloves.
Read all instructions thoroughly and follow any warnings or
cautions attached to any accessed area. Consult local building
codes and the National Electrical Code (NEC) for all applicable
requirements.
Understand the signal words DANGER, WARNING or CAUTION.
These words are universally used for overall safety. DANGER
identifies the most serious hazards, which will result in severe
personal injury or death. WARNING signifies hazards, which
could result in personal injury or death. CAUTION is used to
identify unsafe practices, which would result in minor personal
injury or product and property damage and loss of warranty.
4. General
1. UV360 fixtures are used to bathe surfaces, air or both with
UV-C energy. For surfaces locate the UV360 at known
growth areas such as above the coil and drain pan first,
then other moist areas around humidifiers, etc. They can
also be placed in return, supply and mixed air plenums or
any combination of these locations.
2. Check first for power 120V wall socket availability or 24V
DC and all probable service accesses.
“What’s in the Box?”
UV360
Description
167315-001
UV-C Light Kit*
167315-102
UV Bulb, 17” Phillips
* UV-C Light Kit includes hole saw, installation template,
mounting ring, and 24V DC adapter.
5. Power Requirements
The UV360 is rated at 24V DC 50/60Hz-1 AMP.
6. Installation
(designed for metal plenums/drain pans and ducting):
1. Consult all applicable codes before installing. Check fixture
label(s) for the correct power requirements and supply the
correct voltage from a suitable, protected (fused or breaker),
and grounded power source.
!
CAUTION
Using other than labeled voltages voids warranty and may
damage to the entire system. Operate fixture
continuously to avoid growth of mold and bacteria in
damp areas (when AHU is off) and to extend product life.
2. Power must also be switched, at all install access points,
with a properly rated SPST interlock switch to completely de-
energize the assembly when its install location is accessed.
Accesses are to have signs in appropriate languages
alerting maintenance personnel to the possible hazard of
looking at, or exposing skin to UVC energy (English label(s)
provided).
NOTE: UV-C energy may damage certain plastics.
Protect susceptible items with UV-C resistant materials such
as aluminum tape, foil or aluminum paint when these items
are in “line of sight” of UV-C energy.
3. Determine mounting location and apply template - cut the
hole using the included 2 7/8” hole saw.
4. When installing on duct-board, use the provided Duct-Board
Mounting Plate to provide a stronger mounting surface.
Apply template to the Duct-Board Mounting Plate.
!
CAUTION
Do not drill into refrigerant lines or other critical system
components. After cutting hole, avoid sharp edges.
5. Slide mounting “ring” into hole and affix with 3 Phillips
screws (Image B)
Image A: Mounting Ring
Image B: Mounting Ring
