Trinity SILVER REFERENCE Manual Download Page 8 | Manualshive

Page: 8 / 22

background image

WIRING UP

1. Disconnect the PHONO PREAMP from the power source. Never disconnect any wires unless the device is switched off.

2. Connect the PHONO PREAMP to the tone arm.

3. Connect the PHONO PREAMP to the LINE PREAMP.

4. Connect the PHONO Load Connectors to the load connector XLR inputs.

5. The precision rotary switch can be operated by a coin.

6. Select the matching load for the used MC pick-up.

7. Additional connectors with any values can be ordered as an option.

«
...
6
7
8
9
10
...
»

Summary of Contents for SILVER REFERENCE























Reviews:

No comments

Related manuals for SILVER REFERENCE

Brand: Harman Kardon Pages: 9

Brand: icon Audio Pages: 5

Brand: Yamaha Pages: 101

Brand: Tiger Electronics Pages: 8

Brand: Cable-Tronix Pages: 5

Brand: Kramer Pages: 12

Brand: Knoll Pages: 2

Brand: JDM Pages: 8

REFERENCE PHONO 10

Brand: Audio Research Pages: 18

Brand: Crown Pages: 32

Brand: Echo Pages: 15

Brand: M2TECH Pages: 29

Brand: Altronics Pages: 4

Brand: B&K Pages: 16

Brand: PSSO Pages: 28

Brand: Sonosax Pages: 19

Brand: PowerWave Pages: 21

Brand: Toa Pages: 102

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands