Trigon Monolog Owner'S Manual Download Page 5

 

 

-  

The 

Monolog

 amplifier must not be exposed to shocks or strong vibration. 

-  

The 

Monolog

 amplifier must not be powered up after being moved from a 

cold  location  into  a  warm  environment.  Condensation  may  form  and  could 
damage the appliance. Please wait until the unit is at room temperature and all 
possible  humidity  has  evaporated  before  connecting  the  component  to  AC 
mains. 

The 

Monolog

 amplifier should not be exposed to direct sunlight. 

Do not spill any liquid on the 

Monolog

 amplifier.

 

No liquid should ever

 

be

 

present 

inside the unit.  

-  

Never attempt to operate the component when any part of the chassis is 
removed. 

Before  opening  the  chassis  always  disconnect  the  unit  from  AC  mains 
and wait until all circuits are void of electrical charge.  

-

 

Never bypass any fuse.

 Replace any defective fuse only with the original 

type and value.

Do  not  attempt  to  service  the  unit.  All  maintenance  or 

repair  work  may  only  be  performed  by  authorized  and  specially  trained 
personnel. Any repair, modification or tampering by un unauthorized personnel 
will automatically void all warranty.  

Always  power  down  the  unit  before  connecting  or  disconnecting  signal  and/or 
speaker cables.  

Under  all  circumstances  avoid  electrically  shorting  the  output  connectors.  A 
short  circuit  may  lead  to  immediate  destruction  of  the  amplifier.  Any  damage 
caused by shorting the output is 

not

 covered by warranty.  

Loudspeakers with an impedance less than 2 Ohms are not recommended and 
should not be connected to this amplifier.  

Use only appropriate accessories recommended by the manufacturer.  

 
 
The 

Monolog

  can be operated with AC mains  voltages between 

210

 and 

245

 

Volts,

 normal value is 

230 Volt

. For specific markets  the amplifier can be adapted in 

the factory for 115V or 100V Ac mains respectively. In this case, please contact your 
dealer, distributor or 

Trigon Elektronik G.m.b.H.

 

directly.

 

 

 

 
 

2.2 Installation

 

 

After unpacking please check the unit for any transport damage. In this unlikely event 
please contact your dealer immediately. 
Inspect  the  contents  of  the  package.  Included  with  your 

Monolog

 

amplifier

 

you 

should find these items: 
 

 

 

Trigon

 

Volt 

AC mains cable 

                       

 

-  

Monolog

 

owners manual (1x per pair) 

 

 

-  Warranty card 

 
Install the unit level in a dry and well ventilated location. For sonic considerations we 
recommend  the  use  of  a  proper  audio  equipment  rack  or  amplifier  base.  Strong 

Summary of Contents for Monolog


















Reviews: