Trigon Minipak 4000 Installation & Operation Instructions Download Page 3

Page 3

MP 4000

INTRODUCTION

INTRODUCTION

INTRODUCTION

INTRODUCTION

INTRODUCTION

USE OF THIS MANUAL

This manual contains all of the information required to
successfully install and program the Trigon MP4000.
If you are using this manual to install this unit, it is very
important for you to read the following sections in order:

You should read these instructions before you begin the
installation.  This will insure that everything is done
efficiently.

If you are using this manual as a programming guide
after the initial installation, you will find the TABLE
OF CONTENTS  helpful in locating the particular
programming procedure you desire.

PRODUCT OVERVIEW

PRODUCT OVERVIEW

PRODUCT OVERVIEW

PRODUCT OVERVIEW

PRODUCT OVERVIEW

Figure 1

Telephone Line  - 22 AWG;
Shielded or Twisted,
2 Conductor

Camera, Door or Gate

Secondary

Relay

Serial Printer

(18 AWG; Shielded, 3 Conductor)

Postal

Lock

Box

Primary
Output
Relay

Main Entrance

Power Cabling -
Shielded or Twisted,
2 Conductor,
18AWG  up to  250'
16AWG  up to  500'

Card Reader
(Interface Module Req'd)
18 AWG; Shielded,
4 to 6 Conductor

Alarm
Shunt

Relay

MINIPAK

4000

TRIGON ELECTRONICS
        ORANGE CA.

PUSH START

DIAL NUMBER

9.5"

3.0"

 12.5"

The TRIGON MP4000 is in itself a complete Access
Control Security System.  It makes use of an ordinary
telephone line to provide complete remote control of
an entrance point and/or its monitoring equipment.  It
allows visitors to make contact inside the building they
wish to enter.  Personnel inside the building answer the
incoming telephone call and, with a touch of a button
on their Touch-tone telephone, they grant or deny the
visitor ’s entrance.  Likewise, it allows tenants/
employees a means of direct entry via code or card.

Two relay outputs make it possible to control a camera
as well as a barrier.  Barriers may be latched open under
control of an on-board Time-of-day Clock.  Available
flush mount backboc as well as anoptional lighted hood
add to alternative mounting options.  Records of entry/
exit activity are made possible with a Serial Printer
Output.

Summary of Contents for Minipak 4000













Reviews: