Trigano J- PSC068 Instruction And Maintenance Manual Download Page 12

12 

 

FILTER PARTS INSTALLATION

 

1. 

Insert the tube with the manifold into the container (drawing 2) and screw the 
small sand guard filters to the manifold (drawing 3).

 

2. 

Place the completed manifold on the foundation and fill halfway with water to 
stabilize  it.  Make  sure  that  the  star-shaped  gauze  is  well  centralized  in  the 
bottom of the filter and that the purge screw is tight.

 

3.  Place  the  spigot  on  the  mouth  of  the  container,  making  sure  the  tube  is 

centred on the manifold. 

4.  Fill the filter tank with your filtrering media (if not pre-installed): 

• 

Aqualoon filtering ball: see capacity depending on your filter 

• 

Sand:  approx.  ¾  in  height.  (Ideal  sand  grain  size:  0.7 

–  1.2  mm; 

capacity depending on your filter) (drawing 4). 

5.  Place  the  gasket  under  the  valve.  Place  the  valve  over  the  filter  tank  while 

pressing  it  over  the  tube  with  manifold.  Then  install  the  closing  flange. 
(drawing 7 and 8) 

6.  Put  the  pieces  to  connect  the  filter  to  the  valve.  Make  the  joints  watertight 

with  PTFE  tape.  Be  aware  of  the  wrapping  direction  of  the  tape  (same  as 
screwing direction). 

7.  Install the valve pump hose with the closing flanges provided.

 

 

 
 

 

 

 

 
 

drawing 1 

drawing 3 

drawing 2 

Summary of Contents for J- PSC068


















Reviews: