www.tridonic.com
6
Subject to change without notice. Information provided without guarantee.
Data sheet 10/21-LC896-1
LED Driver
Constant voltage
Automatic circuit breaker type
C10
C13
C16
C20
B10
B13
B16
B20
Inrush current
Installation Ø
1.5 mm
2
1.5 mm
2
2.5 mm
2
2.5 mm
2
1.5 mm
2
1.5 mm
2
2.5 mm
2
2.5 mm
2
I
max
time
LC 100W 48V one4all NF SC EXC
26
34
44
54
13
17
22
27
44.6 A
258 µs
4.7 Harmonic distortion in the mains supply (at 230 V / 50 Hz and full load)
in %
THD
3.
5.
7.
9.
11.
LC 100W 48V one4all NF SC EXC
6
6
1
1
1
1
4.6 Maximum loading of automatic circuit breakers in relation to inrush current
This are max. values calculated out of inrush current! Please consider not to exceed the maximum rated continuous current of the circuit breaker.
Calculation uses typical values from ABB series S200 as a reference.
Actual values may differ due to used circuit breaker types and installation environment.
225
255
DALI
200
175
150
125
100
75
50
25
0
100
90
80
70
60
50
40
30
20
10
0
Dimming characteristics
Digital dimming value
Relative lighting level %
DSI
Dimming characteristics as seen by the human eye
4.8 Dimming
Dimming range 1 % to 100 %
Digital control with:
• DSI signal: 8 bit Manchester Code
Speed 1 % to 100 % in 1.4 s
• DALI signal: 16 bit Manchester Code
Speed 1 % to 100 % in 0.2 s
Programmable parameter:
Minimum dimming level
Maximum dimming level
Default minimum = 1 %
Programmable range 1 %
≤
MIN
≤
100 %
Default maximum = 100 %
Programmable range 100 %
≥
MAX
≥
1 %
Dimming is realized by PWM frequency.
4.9 Dimming characteristics
5. Software / Programming / Interfaces
5.3 Control input DALI
The control input is non-polar for digital control signals (DALI).
The control signal is not SELV. The control cable has to be installed in
accordance to the requirements of low voltage installations.
Digital control with:
• DALI signal: 16 bit
• DSI signal: 8 bit
5.1 Software / programming
With appropriate software and interface different functions can be
activated and various parameters can be configured in the LED Driver.
The Driver supports the following software and interfaces:
Software / hardware for configuration:
• companionSUITE (deviceGENERATOR, deviceCONFIGURATOR,
deviceANALYSER)
• masterCONFIGURATOR
Interfaces for data transfer:
• NFC
• Control input DALI
5.2 Nearfield communication (NFC)
The NFC Interface allows wireless communication with the LED Driver.
This interface offers the option to write configuration and to read
configuration, errors and events with the companionSUITE.
A correct communication between the LED Driver and the NFC antenna
can only be guaranteed if the antenna is placed directly on the Driver.
Any material placed between the LED Driver and the NFC antenna can cause
a deterioration of the communication quality.
After programming the device via NFC power up the device one time for one
second till the deviceANALYSER can read out the parameters.
We recommend the use of following NFC antenna:
www.tridonic.com/nfc-readers
NFC is complied with ISO/IEC 15963 standard.
