background image

TEPP User Manual 

Triangulum Astro Kft. 

 

6

 

Rear panel connectors and switches 

 

 

1)  Motors and limit switches 

Connection for the TEPP’s stepper motors and limit switches. Do not disconnect or 
modify these connectors!  

2)  5V USB out 

Standard USB socket to charge your remote controller. Ouput current is limited to 
200 mA. This port is only for charging, doesn’t support any communication, do not 
connect to your PC or LapTop! 

3)  Hemisphere slection switch 

Use this switch to select the hemisphere according to your location. This switch must 
be set before power on! After you turned on the controller, it is not possible to change 
hemisphere! 

4)  Tracking mode selection switch 

TEPP can be used to track the Sun or the Moon too. Use this switch to select the 
required tracking mode. For standard sky astrophotograpy always set to STAR 
position. Change it only if you’re taking photos of the Sun or Moon! 

 
Before start using the platform, always make sure that the HEMISPHERE swith is in the right 
positon! There is no way to change the hemisphere slection during an active tracking. To do 
that, you have to restart the controller after hemisphere is selected.   
 

2.5.2 Powering up 

To power up the controller, turn off the main switch, then connect a 12 V DC power source to 
the connector  12V IN. Always use this dedicated power input connector for the 12 V power 
supply!  All  of  the  other  connectors 

–  marked  as  12V  OUT-  are  outputs.  You  can  use  the 

attached  12  V  car  cigarette  lighter  adapter,  or  any  other  power  supply  with  12  V  regulated 
output voltage and with a minimum 3 A output current rating. Always take care of the right 
polarity,  however  the  controller  is  protected  against  reverse  polarity.  After  connecting  the 
power to the input, you will hear a short click. This is the sound of the output prtection relay, 
and this is part of the normal operation. Now the 12 V auxiliary outputs are enabled, and you 
can  connect  your  own  devices  to  them  now  (camera  power,  heating  or  cooling  circuits, 
autoguider, etc…). Each output has 4 A maximum output current, and they are shor-tcircuit 

Summary of Contents for TEPP













Reviews: