manualshive.com logo in svg

TRENDware ProXpress TE100-S55, User Manual

Share
Download
TRENDware ProXpress TE100-S55 User Manual Download Page 54

 

54

Appendix G  

Hardware Specifications 

S

WITCH 

S

PECIFICATION

 

• 

Complies to IEEE 802.3 CSMA/CD 10Base-T, 100Base-TX,     
100Base-FX Ethernet Standards 

• 

Complies to IEEE 802.1d Spanning Tree, IEEE 802.2 LLC, 
and ISO 8807-3 standards

 

• 

Switched IEEE 802.3 MAC layer frame size: 64-1518 

• 

NWAY Auto-negotiation for each network port providing 
auto-detection of connected cable type, auto-sensing of full 
or half duplex signaling and auto-configuration 

• 

Store-and-forward packet switching 

• 

Native SNMP management support with Ethernet            
MIB II (RFC 1284) and bridge MIB (RFC 1286) 

• 

VLAN support 

• 

4,096 maximum entries for MAC Address Table 

• 

Comprehensive LED display of the system/port status 

• 

128KB EEPROM (flash memory) for firmware upgrade  

• 

One RS-232D (DB-9) port for Out-of-Band management  

 

(asynchronous, 8-bit data, 1 stop bit, no parity, 19.2K baud) 

• 

Rack mountable (Fits standard 2U EIA 19” rack) 

• 

Five 10/100Mbps LAN ports built-in 

• 

Optional slot for add-on modules 

 

P

ORT 

S

PECIFICATION

 

Summary of Contents for ProXpress TE100-S55


























































Reviews:

No comments

Brands by name

Popular brands

Load more brands