DIGITAL ANGLE RULE REF. DAR/200
Thank you for purchasing this Trend product which should give lasting performance if used
in accordance with these instructions.
INTENDED USE
This accessory is intended to be used to measure the angle and length of a component.
SAFETY
Read and understand the instruction sheet carefully before using. This is
a sensitive precision tool. Do not disassemble or drop it. Please note the
sharp edges, avoid scratching. Store out of reach of children. Do not use as
a toy or as a weapon.
PLEASE KEEP THESE INSTRUCTIONS IN A SAFE PLACE.
7
32NDS
MM
MM
10
20
30
40
50
60
70
80
90
100
110
120
130
140
6
5
4
3
3
2
1
4
5
6
7
2
MM10
220
230
240
250
260
270
280
290300
310
320
330
340
350
360
370
380
390
35mm
Hanging
holes
Locking knob
Battery container
Ruler
LCD
200mm
2.5mm
8mm
200mm
20mm
130 140
2
ZER
O ON OFF
Tighten
Loosen
130 140
2
ZER
O ON OFF
Push
Negative
pole
uppermost
130 140
2
ZER
O ON OFF
Pull
130 140
2
ZER
O ON OFF
Push
ZER
O ON OFF
ON/OFF button
ZERO button
1.
Short press ON/OFF to turn on,
close up both rulers and place on the flat
surface, make sure both ruler’s edges
touch the surface, press ZERO button
to set zero.
PP
C/DAR/200
v1.0
MM
3
2
1
4
5
6
7
MM 10 220 230 240 250 260 270 280 290 300 310 320 330 340 350 360 370 380 390
7
32NDS
MM 10 20 30 40 50 60
70 80 90 100 110 120 130 140
6
5
4
3
2
MM
10
7”
400mm
Metric Scale (standard rule)
Imperial Scale
7”
MM
3
2
1
4
5
6
7
MM 10 220 230 240 250 260 270 280 290 300 310 320 330 340 350 360 370 380 390
7
MM 10 20 30 40 50 60
70 80 90 100 110 120 130 140
6
5
4
3
2
MM
10
7
MM
MM
10
20
30
40
50
60
70
80
90
100
110
120
130
140
6
5
4
3
3
2
1
4
5
6
7
2
MM10
220
230
240
250
260
270
280
290300
310
320
330
340
350
360
370
380
390
7
MM 10 20 30 40 50 60
70 80 90 100 110 120 130 140
6
5
4
3
2
MM
10
7
MM 10 20 30 40 50 60
70 80 90 100 110 120 130 140
6
5
4
3
2
MM
10
MM
3
2
1
4
5
6
7
MM
10
220
230
240
25
0
260
270
280
290
300
31
0
320
330
340
350
36
0
37
0
380
390
7
MM 10 20 30 40 50 60
70 80 90 100 110 120 130 140
6
5
4
3
2
MM
10
MM
3
2
1
4
5
6
7
MM
10
220
230
240
25
0
260
270
280
290
300
31
0
320
330
340
350
36
0
37
0
380
390
2.
Rotate the rule to measure the angle.
Li-lon
Battery Fitting and
Replacement
n
To fit or replace battery push the tab on
the bottom of the LCD.
The edge of the battery container will
appear on the opposite side of the LCD.
n
Pull the battery container out.
n
Remove the old battery. Insert the new
battery type CR2032 3v.
n
Ensure the negative pole of the battery
is uppermost. The positive pole is on
the underside of the battery.
n
Push the battery container back in.
Denotes risk of personal injury, loss of life or damage to the tool in case of
nonobservance of the instructions.
The attention of UK users is drawn to The Provision and Use of Work Equipment
Regulations 1998, and any subsequent amendments. Users should also read
the HSE/HSC Safe Use of Woodworking Machinery Approved Code of Practice
and Guidance Document and any amendments. Users must be competent in
woodworking equipment before using our products.
n
Rotate clockwise to tighten
the moving rule.
n
Rotate anti-clockwise to
loosen the moving rule.
TROUBLE SHOOTING
Problem
Possible Cause
Solution
No display or
Lower voltage, no battery or
Reinstall battery or
ambiguous reading.
incorrect installation of battery.
replace battery.
Erratic display.
Misfunction caused
Press zero to reset
by high vibration or heavy
zero.
swinging of rule.
Number skip or
Internal error.
Remove battery, wait one
frozen display.
minute and replace.
MAINTENANCE
The rule has been designed to operate for a long period of time with the minimum of
maintenance. Continual satisfactory operation depends upon proper tool care and regular
cleaning.
Cleaning
n
Clean with mild liquid soap and damp cloth. Dry with soft cloth. Never immerse in
water. Rule requires no additional lubrication.
Storage
n
Return to packaging after use if it is not to be used for a long time. Store rule in a dry
and shady place. Never leave it outside or in a wet environment. Before storing, it is
recommended to wipe surfaces with an anti-rust oil.
GUARANTEE
All Trend products are guaranteed against any defects in either workmanship or
material, except products that have been damaged due to improper use or maintenance.
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing as waste. Packaging should be sorted for
environmental-friendly recycling. The product, at the end of it’s life, should be sorted for
environmental-friendly recycling.
Batteries and the Environment
This unit uses Lithium Ion (Li-Ion) batteries. When battery pack needs replacing,
we recommend the following: Discharge the energy from the batteries by running
them down completely and then remove from the tool.
Li-Ion cells are recyclable so do not throw them away with household waste. They may
end up in an incinerator or landfill, which must be avoided.
Instead, take the batteries to a Trend Service Agent, your local Trend Stockist or a local
recycling station. If necessary contact your local municipality for disposal information.
The collected batteries will be disposed of properly and/or used for recycling purposes.
DESCRIPTION OF PARTS
Battery Care
WARNING!
Insert battery correctly. Keep batteries away from children. Do
not swallow, open, recharge, or expose to water, fire or high temperature: may explode,
leak and cause damage.
CONFORMITY
DECLARATION
This product conforms with EMC Directive 2004/108/EC.
TECHNICAL DATA
Measuring Range: 000.0° - 999.9° (more than 999.9° will show incorrect display)
Working Temperature: 0°C to +50°C Working Humidity: 85% RH
Working Current: 50 uA Resolution: 0.1° Accuracy: 0.3°
Battery: CR2032 3V Lithium Battery Weight: 162g
Measuring Obtuse
Angles
2.
Rotate the rule to measure the angle.
1.
Short press ON/OFF to turn on,
open up both rulers and place on the flat
surface, make sure both ruler’s edges
touch the surface, press ZERO button
to set zero.
135º
45º
ON/OFF
button: Short press ON/OFF to turn
on, or alternatively move the scale to turn
on the device when at off LCD status. Short
press ON/OFF to turn off the LCD. Long
press ON/OFF for more than 3 seconds to
shut off the whole system. Automatically turns
off in 6 minutes.
ZERO
button: Press ZERO to set zero at any
point when turned on.
OPERATION
Measuring Acute
Angles
