background image

8.6  Warranty and service 

You have purchased a quality product from 
TRELOCK. TRELOCK guarantees the initial 
purchaser for a period of two years from the date 
of purchase that this TRELOCK product is free of 
defects in respect of materials and workmanship, 
and ensures that any defective product is repaired 
or replaced with a new product. Any complaints 
you may have should be addressed directly to 
your dealer/specialist stockist, who should also 
be provided with the relevant purchase receipt. He 
will ensure that your warranty entitlement case is 
handled correctly. The warranty is only valid pro-
viding the product has not been forcibly opened 
or damaged. It does not apply for batteries and 
such parts as are subject to wear and tear. Under 
the terms of this warranty, TRELOCK cannot be 
made liable for any damage occurring due to 
product defects of any kind whatsoever. Other 
legal entitlements in respect of defects remain 
unaffected by this warranty. Any questions you 
may have can also be addressed to TRELOCK’s 
customer service department: 

TRELOCK GmbH, Postfach 7880, 48042 Münster, 
Germany, www.trelock.de.  

Here you can enter your PIN numbers

PIN

Default PIN setting:

My personal PIN: 

PIN-time

Default PIN-time setting:  

My personal PIN time:  

PIN

0     0      0    0

0     6      0   

68

Summary of Contents for COCKPIT2 FC 525




































Reviews: