background image

 

SS40 SURGE OPERATION / MAINTENANCE MANUAL 

PAGE 9

 

WARRANTY 

 

SS40 SURGE SUPPRESSOR 

TREBOR International, Inc. warrants to the purchaser of new equipment 
manufactured by TREBOR to be free from defects in material and workmanship 
when used for its intended purpose under normal operating conditions, and 
maintained according to the Operation/Maintenance Manual. 

TREBOR’s obligation under this warranty is limited to repairing or replacing, at 
TREBOR’s option and at the TREBOR factory, any part or parts thereof which 
shall, within 1 year after delivery thereof to the original purchaser, be 
demonstrated to TREBOR’s satisfaction to have been defective. This warranty 
may be transferred to subsequent owners.  The warranty period is based on the 
original ship date from the factory.  All warranty related freight costs shall be 
borne by the customer. 

Excessive wear to pump components caused by pumping abrasive solutions or 
chemicals, as well as damage caused by ingesting foreign objects shall not be 
covered by this warranty. 

This warranty shall not apply to any equipment which, in the judgment of 
TREBOR, shall have been repaired or altered outside TREBOR’s factory in any 
way, so as to affect its performance or reliability; subjected to misuse, negligence 
or accident; or used other than in accordance 

with TREBOR’s printed 

instructions. 

There are no terms, conditions or warranties, expressed, implied or 
statutory, of merchantability, fitness, capacity, or otherwise, of the goods 
ordered, other than, or different from, the warranty set forth above.   This 
warranty takes precedence over any other warranty, expressed or implied.

 

TREBOR neither assumes, nor authorizes any other party to assume for it, any 
liability in connection with said equipment except as set forth above. 

Summary of Contents for SS40










Reviews: