Traxxas TRX 2.5R Owner'S Manual Download Page 4 | Manualshive

Page: 4 / 40

Traxxas TRX 2.5R Owner'S Manual Download Page 4

TRX 2.5R • 4

All instructions and
precautions outlined in
this manual should be
strictly followed to ensure
safe operation of your
TRX 2.5R Racing Engine.

The TRX 2.5R Racing Engine
is not intended for use by
those under 16 years of
age without the supervision
of a responsible and
knowledgeable adult.

Safety Precautions

All of us at Traxxas want you to safely enjoy your new TRX 2.5R Racing Engine. Operate your TRX
2.5R sensibly and with care, and it will be exciting, safe, and fun for you and those around you.
Failure to operate your TRX 2.5R in a safe and responsible manner may result in property damage
and serious injury. The precautions outlined in this manual should be strictly followed to help
ensure safe operation. You alone must see that the instructions are followed and the precautions
are adhered to.

Important Points to Remember

• R/C fuel is dangerous and highly poisonous. Always follow all directions and precautions printed

on the fuel container.

• R/C fuel, especially when in a fuel dispensing bottle, may look like a cool drink to a child.

Keep all

fuel out of the reach of children at all times.

Do not place fuel containers on the ground where

children can get to them while you are driving.

• R/C fuel is flammable. Never allow smoking, sparks, heat or flame in the presence of fuel

or fuel vapors.

• The engine and exhaust system may become extremely hot during use. Be careful not to touch

the parts, especially when refueling or stopping the engine.

• Prolonged exposure to the engine exhaust can be harmful. Avoid breathing the engine exhaust.

Always run your TRX 2.5R outdoors, in a well-ventilated area. Never run the engine indoors.

• Don’t operate your model at night or anytime your line of sight to the model may be obstructed

or impaired in any way.

• Never operate your model in crowds of people or busy pedestrian areas. The TRX 2.5R makes

models extremely fast and may cause injury to those unaware of its presence.

• The engine can be loud. If the noise makes you uncomfortable, wear ear protection. Be

considerate of your neighbors by not running your model early in the morning or late
in the evening.

•

Most importantly, use good common sense at all times.

SAFETY PRECAUTIONS

«
...
2
3
4
5
6
...
»

Summary of Contents for TRX 2.5R









































Reviews:

No comments