6 • T-MAXX 3.3 OWNER’S MANUAL
Tire Gluing
The factory tires on your T-Maxx 3.3 are already glued to the rims.
The tires must be glued to the rims to prevent the rims from spinning
inside the tires. The instructions here are provided to show you how
to glue replacement tires to the rims in the future. Use CA tire glue,
such as Traxxas Ultra Premium Tire Glue (part #6468). You can glue the
tires without removing the wheels from the truck. For clarity, these
instructions show the process with the wheels removed.
1. Remove a wheel from T-Maxx 3.3 using the
larger (8mm) end of the universal (glow
plug) wrench.
2. Use your thumb to push the side of the tire
away from the rim. Place one or two drops
of CA glue into the opening and release
the tire. Capillary action will draw the glue
around the bead of the tire.
3. Repeat step two at four or five points around the rim, until the tire is
completely secured to the rim. Turn the rim over and repeat the process
for the inside of the rim/tire. Repeat for the other three wheels.
4. Reinstall the wheels, make sure none of the axle pins have fallen out from
behind the hex hubs.
Applying the Decals
The main decals
have already been
applied to your T-Maxx 3.3. The extra
decals provided are die-cut for easy
removal. Use a hobby knife to lift the
corner of a decal and remove it from
the backing.
Carefully position the decal over the
desired location and press one side on
the body. Pull the decal tight and use a
finger to gradually smooth out any air
bubbles as you apply the decal.
Look at the photos on the box for
typical decal placement.
The following guide is an overview of the procedures for getting your model running. Look for the Quick Start logo on Quick
Start entries. The Quick Start Guide is not intended to replace the full operating instructions available in this manual. Please
read this entire manual for complete instructions on the proper use and maintenance of your model.
1. Read the safety precautions on page 3
9.
Fill the fuel tank • See page 14
For your own safety, understand where carelessness and misuse could
lead to personal injury.
Use your fuel-dispensing bottle (sold separately) to fill the tank.
2. Charge the EZ-Start battery pack • See page 17
10. Connect the EZ-Start to the model • See page 17
The EZ-Start requires a fully charged 7.2-volt battery pack.
Learn the proper way to use the EZ-Start electric starting system.
3. Install batteries • See page 8
11. Start the engine • See page 18
T-Maxx 3.3 requires 8 AA alkaline batteries for the transmitter (4) and
receiver (4) (sold separately).
Learn to use the correct starting procedure for your TRX 3.3.
4. Decal and Install the body • See below
12. Break-in your engine • See page 18
You will need to use the body during break in, so it’s best to apply any
additional decals before you use the body.
Follow the break-in instructions exactly to ensure the best-performing,
longest-lasting engine.
5. Install the EZ-Start battery • See page 17
13
.
Tune your engine • See page 20
Install and connect a charged 7.2-volt battery pack in the
EZ-Start controller.
Learn how to set the fuel mixture needles for optimum
engine performance.
6. Turn on the radio system • See page 9
14. Drive your T-Maxx 3.3 • See page 22
Make a habit of turning the transmitter on first, and off last.
Learn to use the two-speed functions on your truck,
along with important driving precautions.
7. Check servo operation • See page 9
15. Maintaining your Truck • See page 27
Make sure the throttle and steering servos are
working correctly.
Follow these critical steps to maintain the performance of your
T-Maxx 3.3 and keep it in excellent running condition.
8. Range test the radio system • See page 10
Follow this procedure to make sure your radio system works properly
at a distance and that there is no interference from outside sources.
GLUING TIRES AND DECORATING YOUR T-MAXX 3.3
QUICK START: GETTING UP TO SPEED
