background image

26 • T-MAXX 3.3 OWNER’S MANUAL

acceleration by reducing engine rpm loss when shifting from 1st gear to 
2nd gear. The wide ratio gear set is designed for wide open areas and will 
increase top speed, but reduce acceleration due to greater rpm loss when 
shifting gears.

BRAKE SETUP & ADJUSTMENT

T-Maxx 3.3 is equipped with a disc brake that rides on the yoke of the 
transmission’s front output shaft. The brake is preset at the factory 
and should not require attention. As the brake material wears, future 
adjustments may be necessary.

Brake Shoulder Screw Adjustment
The two shoulder bolts that are used to secure the brake pads to the 
transmission housing may need to be adjusted periodically as the brake 
material wears down. They should be tightened so a 0.50mm (.020”) gap
exists between the disc and the brake pad (on the transmission side). 
Adjust in one of the following ways: 

1.

 

Use a .50mm feeler gauge between 

the brake pad insert and brake disc.

2.

 

Push the outer brake pad firmly 

against the inner pad with your 
finger, sandwiching the brake disc 
between the brake calipers. Tighten 
the brake shoulder bolts until they just barely touch the brake pads. Do 
not over tighten these fasteners or you could damage the brake calipers. 
Loosen each of the shoulder bolts by 1 turn.

Brake Pad Wear and Replacement
During normal use the brake pads should wear at a relatively slow rate.   
However, if the brake pads wear down close to the metal pad holders, they 
should be replaced. Any more wear than this could cause damage to the 
brake parts and improper operation of the brake system.

WHEELIE BAR SETUP & ADJUSTMENT

Wheelie Bar Installation
The Maxx Wheelie Bar can be used on any Maxx truck with the  
stock rear skid plate, rear bumper, and rear bumper mounts.  
It is also compatible with the Traxxas accessory aluminum rear 
bumper (part #4935X). The wheelie bar is intended for use on hard, 
high-traction surfaces, such as pavement, where controlling wheelies 
can be difficult. It is easily removed for off-road racing or jumping.

1. Slowly bend the end of the skid plate downward, and then key the  

skid plate into the slot of the wheelie bar. 

2.

 

Slide the wheelie bar down to the bottom of the skid plate,  
and then snap the clip over the lower bumper tube. 

3. Removal is opposite of installation. Snap the wheelie bar off of the 

bumper, and then slide the wheelie bar off of the skid plate.

Wheelie Bar  Setup Instructions
Changing the position of the wheelie 
bar height setting is easier when 
the wheelie bar is installed on the 
truck. Snap the upper arms off of the 
wheelie position cross bars. Move the 
upper arms to the desired wheelie 
position cross bar and then snap them 
in place. 

Each setting can offer different results based on the individual ride 
height and droop settings for a particular truck. Try to avoid riding on 
the wheelie bar wheels during normal driving (this can happen in the 
lowest setting with lower than stock ride heights).

Remove the wheelie bar when the T-Maxx will be jumped or driven in 
harsh off-road conditions.

TUNING ADJUSTMENTS

0.5mm

gap

Position 1 (big wheelies)

Bottom position on 
cross bars. Allows 
the truck to tip back 
the furthest during 
a wheelie for longer, 
high-speed wheelies. 

Position 2

Position 4 (no wheelies)

The top position on 
cross bars. Offers the 
flattest launches with 
little or no wheelie. 
This is the factory 
installed position 
to reduce wheelies 
during break-in.

Position 3

Upper Arms

Position 

Cross Bars

Summary of Contents for T-Maxx 3.3 49077

































Reviews: