background image

12 • STAMPEDE 4x4 VXL

4,5

INSTALLING THE 
BATTERY PACK

Install the battery pack with the 
battery wires facing the rear 
of the model. Insert the tabs 
of the battery hold-down into 
the slots in the rear hold-down 
retainer and then place the 
battery hold-down over the 
post. Secure the battery hold-
down with body clip in the hole 
in the post.  Do not connect the 
battery pack yet.

Using a Different Battery Configuration

The battery hold-down is capable of accommodating either side-
by-side racing style packs, “hump packs” with a stacked seventh 
cell, or the more common stick packs. The battery compartment is 
configured for stick packs from the factory. The number on each 
side of the hold-down indicates the battery height in millimeters 
that hold-down can accommodate. Note that one side is labeled 
“25” and the other side is labeled “23”. The 25mm side is for use 
with typical stick type battery packs. If you are using side-by-side 
racing packs, simply flip the hold-down over to the 23mm side and 
use it on the opposite side of the chassis. 

Note

: For taller batteries, 

an extended battery hold-down, part #6727X, is available (sold 
separately). For shorter batteries (6-cell), us the included foam 
block in the front of the battery compartment.

RADIO SYSTEM RULES 

• Always turn your TQi transmitter on first and off last. This 

procedure will help to prevent your model from receiving stray 
signals from another transmitter, or other source, and running 
out of control. Your model has electronic fail-safes to prevent this 
type of malfunction, but the first, best defense against a runaway 
model is to always turn the transmitter on first and off last.

25mm side: Standard 

NiMH stick pack setup

23mm side: Side-by-side 

NiMH pack setup

Battery Compartment Specs:
• 142mm (5.59

"

) long  

x  49.5mm (1.95

"

) wide

• Height with stock strap:  

23mm (.91

"

) or 25mm (.94

"

)

• Height with Part #6727X 

options battery standoffs:   
Up to 44mm (1.73

"

)

Note: There is some flex with 
the battery strap.  It is possible 
to fit slightly taller batteries in 
the compartment.

TRAXXAS TQ

i

 RADIO & VELINEON POWER SYSTEM

Battery iD

Your model’s included battery 
pack is equipped with Traxxas 
Battery iD. This exclusive 
feature allows Traxxas battery 
chargers (sold separately) 
to automatically recognize 
connected battery packs 
and optimize the charge 
settings for the battery. 
This eliminates the need to 
worry over charger settings 
and menus for the easiest 
and safest charging solution 
possible. Visit Traxxas.com to 
learn more about this feature 
and available Traxxas iD 
chargers and batteries.

RADIO SYSTEM CONTROLS

Forward

Neutral

Brake/Reverse

TURN

 R

IG

H

T

T

U

R

N

 LE

FT

Always turn your

transmitter on first.

Turn on the model.

1

2

Plug in the battery.

3

Summary of Contents for Stampede 4x4 VXL 67086-1



































Reviews: