background image

20 • SPARTAN

Adjusting the Trim Tabs

Spartan features stainless-steel trim tabs to help set the angle of the boat’s hull as it rides in the water. Setting the trim angle correctly will 
provide maximum speed and efficiency from your model. From the factory, the trim tabs are set for best all-around performance and stability 
at Spartan’s maximum speed, but you can experiment with their position to improve performance. Slightly bending the tabs down will cause 
the bow to run closer to the water, “wetting” more of the hull and increasing stability. Be sure to set the left and right trim tabs equally. 

ADJUSTING YOUR MODEL

Hold a straightedge against the hull so it 
extends past the trim tab. The tab will rest 
on the straightedge or be within 1mm of 
its edge. This is the stock setting. Rigorous 
testing has shown this setting to offer the 
best handling in most conditions.

To adjust the trim tab, 
grip it securely with a pair of 
pliers as close to the bend as 
possible. Flex the trim tab down 
to set a new angle. Note that the 
trim tab has some spring-back, 
and will need to be flexed slightly 
farther than the actual position 
you wish to set. 

This illustration shows 1mm of 
downward defection. This small setting 
will cause a significant change in the 
hull’s attitude. Settings of 2-3mm 
deflection should be considered  
the maximum. 

A

B

C

Optional Accessory: Machined 
Aluminum Trim Adjusters

For the most precise trim 
adjustments, Spartan can 
be outfitted with machined 
aluminum trim adjusters. 

These install using the 
existing trim tab mounting 
holes, so no drilling is 
required. Once installed, 
the adjusters’ stainless-
steel screws can be used 
to make fine trim settings. 
Once Spartan is trimmed to 
your preference, corrosion-
resistant nickel-plated nuts 
hold the adjustment. Refer 
to the parts list for more 
information and accessories.

Rudder Angle 

Adjustment Screws

Stock Position

 0° 

(Parallel to back of boat)

2°-3°

Adjusting the Rudder Angle

Spartan features an adjustable rudder support that permits the angle 
of the rudder to be changed to alter the model’s cornering feel. The 
stock setting is 0°, or ‘vertical,’ meaning the rudder is parallel with the 
transom (see illustration). By loosening the rudder angle adjustment 
screws, the rudder can be pivoted back up to 3°. Altering the rudder 
angle effects how much the rudder ‘lifts’ the hull while cornering. 
Increasing the rudder angle will allow the hull to ride higher while 
cornering, which may potentially raise cornering speeds but also 
lessens stability. If you experiment with this feature, remember to 
retighten the adjustment screws after making your setting.

Summary of Contents for Spartan 5707































Reviews: