Traxxas Slash 4x4 68086 Owner'S Manual Download Page 32

Page: 32 / 34

ADVANCED TUNING GUIDE

Set Multi-Function
knob for STEERING
SENSITIVITY (Expo)

Press/hold MENU

green LED blinks

Press SET

red LED blinks

Press SET to confirm

green LED blinks (x8)

Press/hold MENU

returns to driving mode

Set Multi-Function
knob for THROTTLE
SENSITIVITY (Expo)

Press/hold MENU

green LED blinks

Press SET

red LED blinks

Press MENU to confirm

red LED blinks (x2)

Press SET to select

green LED blinks (x8)

Press/hold MENU

returns to driving mode

Set Multi-Function
knob for STEERING
Dual-Rate (%)

Press/hold MENU

green LED blinks

Press SET

red LED blinks

Press MENU twice

red LED blinks (x3)

Press SET to select

green LED blinks (x8)

Press/hold MENU

returns to driving mode

Set Multi-Function
knob for BRAKING
PERCENTAGE (%)

Press/hold MENU

green LED blinks

Press SET

red LED blinks

Press MENU 3 times

red LED blinks (x4)

Press SET to select

green LED blinks (x8)

Press/hold MENU

returns to driving mode

Set Multi-Function
knob for
THROTTLE TRIM

Press/hold MENU

green LED blinks

Press SET

red LED blinks

Press MENU 4 times

red LED blinks (x5)

Press SET to select

green LED blinks (x8)

Press/hold MENU

returns to driving mode

Adjust the Multi-

Function knob until the

LED turns solid green.

To LOCK the
Multi-Function knob

Press/hold MENU

green LED blinks

Press SET

red LED blinks

Press MENU 5 times

red LED blinks (x6)

Press SET to lock

green LED blinks (x8)

Press/hold MENU

returns to driving mode

To REVERSE
the direction of
STEERING servo

Press/hold MENU

green LED blinks

Press MENU

green LED blinks (x2)

Press SET

green LED blinks

Press SET

red LED blinks

Press SET

to reverse

servo direction

Press/hold MENU

returns to driving mode

To set the SUB TRIM
of the STEERING
servo

Press/hold MENU

green LED blinks

Press MENU

green LED blinks (x2)

Press SET

green LED blinks

Press SET

red LED blinks

Press MENU

red LED blinks (x2)

Use Multi-Function

knob

to set neutral

Press SET

to save position

Press/hold MENU

returns to driving mode

To set the END
POINTS of the
STEERING servo

Press/hold MENU

green LED blinks

Press MENU

green LED blinks (x2)

Press SET

green LED blinks

Press SET

red LED blinks

Press MENU twice

red LED blinks (x3)

Turn steering

wheel

to desired max

left and right travel

Press SET

to save each position

Turn steering wheel

to test settings

IF END POINTS

ARE OK:

Press/hold MENU

returns to driving mode

IF END POINTS

NEED TO BE

CHANGED:

Press SET

and repeat steps 6-8

To reset the END
POINTS of STEERING
servo to defaults

Press/hold MENU

green LED blinks

Press MENU

green LED blinks (x2)

Press SET

green LED blinks

Press SET

red LED blinks

Press MENU 3 times

red LED blinks (x4)

Press SET

to reset end points

Press/hold MENU

returns to driving mode

To REVERSE
the direction of
THROTTLE servo

Press/hold MENU

green LED blinks

Press MENU

green LED blinks (x2)

Press SET

green LED blinks

Press MENU

green LED blinks (x2)

Press SET

red LED blinks

Press SET

to reverse

servo direction

Press/hold MENU

returns to driving mode

To set the SUB TRIM
of the THROTTLE
servo

Press/hold MENU

green LED blinks

Press MENU

green LED blinks (x2)

Press SET

green LED blinks

Press MENU

green LED blinks (x2)

Press SET

red LED blinks

Press MENU

red LED blinks (x2)

Use Multi-Function

knob

to set neutral

Press SET

to save position

Press/hold MENU

returns to driving mode

To set the END
POINTS of the
THROTTLE servo

Press/hold MENU

green LED blinks

Press MENU

green LED blinks (x2)

Press SET

green LED blinks

Press MENU

green LED blinks (x2)

Press SET

red LED blinks

Press MENU twice

red LED blinks (x3)

Use throttle

trigger

to set desired

max throttle or brake

Press SET

to save

Use trigger to test

IF END POINTS

ARE OK:

Press/hold MENU

returns to driving mode

IF END POINTS

NEED TO BE

CHANGED:

Press SET

and repeat steps 7-9

To reset the END
POINTS of THROTTLE
servo to defaults

Press/hold MENU

green LED blinks

Press MENU

green LED blinks (x2)

Press SET

green LED blinks

Press MENU

green LED blinks (x2)

Press SET

red LED blinks

Press MENU 3 times

red LED blinks (x4)

Press SET

green LED blinks (x8)

Press/hold MENU

returns to driving mode

MENU TREE FORMULAS

To select functions and make adjustments to the TQi transmitter without
referencing the Menu Tree, turn your transmitter on, find the function in the
left column you wish to adjust, and simply follow the corresponding steps.

Always turn your

transmitter on first.

Summary of Contents for Slash 4x4 68086



































Search results

Summary of Contents for Slash 4x4 68086

Reviews:

Related manuals for Slash 4x4 68086

Brands by name

Popular brands

Traxxas Slash 4x4 68086, Owner'S Manual

Search results

Summary of Contents for Slash 4x4 68086

Reviews:

Related manuals for Slash 4x4 68086

Brands by name

Popular brands