background image

24 • REVO 3.3

Installing the EZ-Start Battery

1.  Press the tab in the end of the battery 

compartment door to open (A).

2.  Plug a fully charged 7.2-volt 

battery pack into the  
connector inside (B).

3.  Twist the battery two or 

three times to twirl the 
battery plug wires. This 
helps hold the wire and 
battery in place when the 
battery is installed in the 
compartment (C).

4.  Install the battery into the 

compartment and press the wires securely into place.

5.  Snap the battery compartment door back on and lock the  

end tab (D).

Using the EZ-Start

Your EZ-Start controller plugs into a 4-prong receptacle in the center of the 
bed on your Revo 3.3. When the red button on the controller is pressed, 
the EZ-Start motor begins to spin the engine and power from the control 
unit heats the glow plug. Assuming all settings and preparations are 
correct, the engine should start almost immediately.
Each of the two status indicator LEDs on the hand-
held control unit, the 

Motor 

LED and the 

Glow Plug

 

LED, should light green while starting. If either LED 
fails to light while starting, there is a fault indicated 
with that function.

If the Glow Plug LED fails to light, the glow plug may 
be bad, or the glow plug wire may be damaged or 
disconnected.

If the Motor LED fails to light and the starter fails to 
operate, then the EZ-Start is in protection mode.

Protection Mode

The EZ-Start uses Smart Start

 technology to monitor the condition 

of the system and detect failures. The controller monitors the load 
being placed on the EZ-Start motor. If the load becomes excessive, 
the system shuts off power to the motor to prevent costly damage 
to the motor and the controller. This may occur, for example, if the 
engine floods with fuel during starting. The starter spins at first but 
when excessive fuel in the combustion chamber begins to lock up the 
engine, the starter motor slows under the heavier load. This causes 
the protection circuit to shut off the power to the motor. Allow at least 
3 minutes for the starter motor to cool and the circuit to automatically 
reset before continuing. Use the time to find and eliminate the 
condition that caused the excessive load on the starter motor.

Use a Strong Starter Battery 

A weak starter battery, or one that has not been fully charged, may 
not deliver enough power to crank the engine over at the appropriate 
rpm to keep the piston from sticking at top dead center (TDC). A new 
engine will typically have a tight fit between the piston and the top of 
the sleeve. This is a tapered fit, and a tight piston sleeve fit on initial 
startup is desirable for those who want the best-performing engine. 
Make sure you are using a good quality battery pack that is fully 
charged (new batteries usually require several charge cycles to reach 
peak voltage and full capacity). This is especially important with a new 
engine that needs to be broken in. If the engine sticks at TDC, see 
page 38 for instructions on freeing the engine.

Shutting Off The Engine

Turning off the switch for the radio will not 
shut off the engine. To shut off the engine, use 
the shut-off clamp on the fuel line. Squeeze 
the clamp closed to shut off the fuel supply to 
the engine. Don’t forget to release it when you 
restart the engine.
Avoid shutting off the engine by placing your finger over the exhaust 
outlet, especially if you are through driving for the day. This will 
leave more unburned fuel in the engine that could lead to harmful 
corrosion. 

Always be careful not to touch the exhaust pipe after 

running, it can become very hot.

Using Other Chargers

Another convenient option 
for charging the included 
battery is an AC peak-
detecting charger that plugs 
directly into an AC wall 
outlet. It contains special 
peak-detection circuitry 
that automatically shuts the 
charger off when the battery 
is fully charged.

Caution

: Never use a 

15-minute timed charger to 
recharge your model’s battery 
packs. Overcharging may 
result, causing damage to the 
battery packs.

A

B

C

D

Motor

Glow  Plug

Motor

Glow  Plug

Motor

Glow  Plug

Motor

Glow  Plug

Motor

Glow  Plug

Motor

Glow  Plug

Motor

Glow  Plug

Motor

Glow  Plug

Motor

Glow  Plug

Motor

Glow  Plug

Motor

Glow  Plug

Motor

Glow  Plug

Motor

Glow  Plug

Motor

Glow  Plug

Motor

Glow  Plug

Motor

Glow  Plug

Motor

Glow  Plug

Motor

Glow  Plug

Motor

Glow  Plug

Motor

Glow  Plug

Motor

Glow  Plug

Motor

Glow  Plug

Motor

Glow  Plug

Motor

Glow  Plug

Motor

Glow  Plug

Motor

Glow  Plug

Motor

Glow  Plug

When the EZ-Start controller 
is in protection mode, wait 
at least three minutes before 
attempting to start the 
engine, to give the starter 
motor time to cool.

It’s normal for your EZ-Start 
controller to become warm  
after repeated use.

THE TRX 3.3 RACING ENGINE

5

,

10

Summary of Contents for Revo 3.3 53097

















































Reviews: