background image

22 • TRX-4M

MAINTAINING YOUR MODEL

Your model requires timely maintenance in order to stay in top 
running condition. 

The following procedures should be taken 

very seriously.

Inspect the vehicle for obvious damage or wear. Look for:

1.  Cracked, bent, or damaged parts
2.    Check the wheels and steering for binding. 
3.    Check the operation of the shocks. 
4.    Check the wiring for any frayed wires or loose connections.
5.    Check the mounting of the electronic control module (ECM) 

and servo.

6.    Check the tightness of the wheel nuts with a wrench.
7.    Check the operation of the radio system, especially the 

condition of the batteries.

8.    Check for any loose screws in the chassis structure  

or suspension. 

Other periodic maintenance:

• 

Chassis:

 Keep the chassis clean of accumulated dirt and grime. 

Periodically inspect the chassis for damage.

• 

Shocks:

 Keep the oil level in the shocks full. Use only 100% 

pure silicone shock oil to prolong the life of the seals. If you are 
experiencing leakage around the top of the shock, inspect the 
bladder for signs of damage or distortion from overtightening. 
If the bottom of the shock is leaking, then it is time for a rebuild. 
The Traxxas rebuild kits for two shocks are part #9762 and 9762A.  

• 

Suspension:

 Periodically inspect the model for signs of damage, 

such as bent linkage rods, bent shock shafts, loose screws, or any 
signs of stress or bending. Replace components as needed.

• 

Center Driveline:

 Inspect the driveline for signs of wear such 

as worn or dirty center drive shafts, and any unusual noise or 
binding. Do not allow dirt and grime to collect in the drive cups. 
Tighten, clean, or replace components as needed.

• 

Transmission:

 Periodically remove the transmission from 

the model and inspect for any signs of damage. Disassemble 
and clean the transmission components. Replace components 
as needed. Complete Pro-Built

®

 transmission assemblies are 

available as part #9791, 9791R, or 9791X.

• 

Front and Rear Axles:

 Remove and clean the front and rear axles as 

needed. Replace any damaged components.  

Storage

When you are through running the model for the day, blow it off 
with compressed air or use a soft bristled paint brush to dust-off 
the vehicle. Always disconnect and remove the battery from the 
model whenever the model is stored. If the model will be stored for 
a long time, then also remove the batteries from the transmitter.

If you have questions or need technical assistance, call Traxxas at

1-888-TRAXXAS

 

(1-888-872-9927) (U.S. residents only)

Always wear eye protection 
when using compressed 
air or spray cleaners and 
lubricants.

7

7

Summary of Contents for 97054-1
























Reviews: