manualshive.com logo in svg

Traxxas 4902, Owner'S Manual, Page: 8 / 48

Share
Download
Traxxas 4902 Owner'S Manual Download Page 8

8

•

T-MAXX 2.5R

Applying The Decals

The main decals have already been
applied to your T-Maxx 2.5R. The extra
decals provided are die-cut for easy
removal. Use a hobby knife to lift the
corner of a decal and remove it from
the backing. 

Carefully position the decal over the
desired location and press one side on
the body. Pull the decal tight and use
a finger to gradually smooth out any
air bubbles as you apply the decal. 

Look at the photos on the box for
typical decal placement.

Tire Gluing

The factory tires on your T-Maxx 2.5R are already glued to the rims. The
tires must be glued to the rims to prevent the rims from spinning inside
the tires. The instructions here are provided to show you how to glue
replacement tires to the rims in the future. Use CA tire glue available
from your local hobby dealer. You can glue the tires without removing
the wheels from the truck. For clarity, these instructions show the
process with the wheels removed.

Gluing the Tires and Decorating your T-Maxx 2.5R

1. 

Remove a wheel from T-Maxx

2.5R using the larger (8mm) end
of the glow plug (universal)
wrench.

2.

Use your thumb to push the side

of the tire away from the rim.
Place one or two drops of CA
glue into the opening and
release the tire. Capillary action
will draw the glue around the
bead of the tire.

3.

Repeat step two at four or five

points around the rim, until the
tire is completely secured to the
rim. Turn the rim over and repeat
the process for the inside of the
rim/tire. Repeat for the other
three wheels.

4. 

Reinstall the wheels, make sure

none of the axle pins have fallen
out from behind the hex hubs. 

Always wear safety glasses
to prevent glue from
splattering into your eyes.

The acetone in fingernail
polish remover will
remove excess glue from
your fingers.

For best results while
gluing, clean the bead of
the tires and the grooves
of the wheels with
denatured alcohol before
applying glue. This
removes any mold release
agent residue from the
tires and wheels,
providing a better bond.

Summary of Contents for 4902

















































Reviews:

No comments