background image

4 • TR A X X AS

This model is not intended 
for use by children under 
8 years of age without the 
supervision of a responsible 
and knowledgeable adult. 
Gearing and battery choice 
(

see LiPo Batteries, right)

 

effect the skill level of the 
model. See chart below.

All instructions and 
precautions outlined in this 
manual should be strictly 
followed to ensure safe 
operation of your model.

Safety Precautions

All of us at Traxxas want you to safely enjoy your new model. Operate 
your model sensibly and with care, and it will be exciting, safe, and fun 
for you and those around you. Failure to operate your model in a safe and 
responsible manner may result in property damage and serious injury. 
The precautions outlined in this manual should be strictly followed to help 
ensure safe operation. You alone must see that the instructions are followed 
and the precautions are adhered to. 

Important Points to Remember

  Your model is not intended for use on public roads or congested  

areas where its operation can conflict with or disrupt pedestrian or 
vehicular traffic.

  Never, under any circumstances, operate the model in crowds of  

people. Your model is very fast and could cause injury if allowed to 
collide with anyone.

  Because your model is controlled by radio, it is subject to radio 

interference from many sources that are beyond your control. Since  
radio interference can cause momentary losses of radio control, always 
allow a safety margin in all directions around the model in order to 
prevent collisions. 

  The motor, battery, and speed control can become hot during use. Be 

careful to avoid getting burned.  

  Don’t operate your model at night, or anytime your line of sight to the 

model may be obstructed or impaired in any way.

 

Most importantly, use good common sense at all times.

Batteries and Battery Charging

Your model uses rechargeable batteries that must be handled with care for 
safety and long battery life. Make sure to read and follow all instructions and 
precautions that were provided with your battery packs and your charger. It 
is your responsibility to charge and care for your battery backs properly. In 
addition to your battery and charger instructions, here are some more tips 
to keep in mind.

  Never leave batteries to charge unattended.
  Remove the batteries from the model while charging.
  Always unplug the battery from the electronic speed control when the 

model is not in use and when it is being stored or transported.

  Allow the battery packs to cool off between runs (before charging).
  Do not use battery packs that have been damaged in any way.
  Do not use battery packs that have damaged wiring, exposed wiring, or a 

damaged connector. 

  Children should have responsible adult supervision when charging and 

handling batteries.

LiPo Batteries

Lithium Polymer (LiPo) batteries are becoming popular for use in R/C 
models due to their compact size, high energy density, and high-current 
output. However, these types of batteries require special care and handling

procedures for long life and safe operation. 

Warning:

 LiPo batteries are 

intended only for advanced users that are educated on the risks associated 
with LiPo battery use. 

Traxxas does not recommend that anyone under 

the age of 16 use or handle LiPo battery packs without the supervision of 
a knowledgeable and responsible adult. 

Your model is able to use LiPo batteries with nominal voltage not to exceed 
11.1 volts (3S packs) volts. LiPo batteries have a minimum safe discharge 
voltage threshold that should not be exceeded. The Velineon VXL-3s 
electronic speed control is equipped with built-in Low-Voltage Detection 
that alerts the driver when LiPo batteries have reached their minimum 
voltage (discharge) threshold.

 

It is the driver’s responsibility to stop 

immediately to prevent the battery pack from being discharged below its 
safe minimum threshold.

Low-Voltage Detection on the speed control is just one part of a 
comprehensive plan for safe LiPo battery use.

 

It is critical for you, the user, 

to follow all other instructions supplied by the battery manufacturer and 
the charger manufacturer for proper charging, use, and storage of LiPo 
batteries. Make sure you understand how to use your LiPo batteries. 

Be 

aware that Traxxas shall not be liable for any special, indirect, incidental, 
or consequential damages arising out of the installation and/or use of LiPo 
batteries in Traxxas models.

If you have questions about LiPo battery usage, please consult with your 
local hobby dealer or contact the battery manufacturer. 

As a reminder, 

all batteries should be recycled at the end of their useful life. Do not throw 
batteries away in the trash. Ask your hobby dealer for the location of the 
closest recycling center or go online to www.rbrc.org (Rechargeable Battery 
Recycling Corporation) to find a recycling center near you.

Speed Control

  Water and Electronics Do Not Mix: Do not operate the model in or around 

water. Never allow water, moisture, or other foreign materials to get 
inside the speed control.

  Disconnect the Batteries: Always disconnect the battery pack from  

the speed control when not in use. 

  Transmitter on First: Switch on your transmitter first before switching on 

the speed control to prevent runaways and erratic performance.

  Don’t Get Burned: The heat sink can get extremely hot, so be careful not 

to touch it until it is cool. Supply adequate airflow for cooling.

  Use Stock Connectors: If you decide to change the battery or motor 

connectors, only change one battery or motor connector at a time.  
This will prevent damage from accidentally mis-wiring the speed control. 
Please note that modified speed controls can be subject to a rewiring fee 
when returned for service. Removing the battery connector on the speed 
control or using the same-gender connectors on the speed control will 
void the product’s warranty.

  Insulate the Wires: Always insulate exposed or damaged wiring with heat 

shrink tubing to prevent short circuits

<ZVg^c\/ HidX`E^c^dc

7ViiZgn/ +"8ZaaC^B=

KdaiV\Z

/ ,#'K

b6]/

(%%% BV]

<ZVg^c\/ Dei#E^c^dc

7ViiZgn/ ,"8ZaaC^B=

KdaiV\Z

/ -#)K

b6]/

)%%% BV]

<ZVg^c\/ Dei#<ZVg^c\

7ViiZgn/ (H'%8A^Ed

KdaiV\Z

/ &&#&K

b6]/

)%%% b6]

<ZVg^c\/ Dei#<ZVg^c\

7ViiZgn/ (H'%8A^Ed

KdaiV\Z

/ &&#&K

b6]/

-%%%b6]

Cdb^cVa

1

See the gearing chart on page 
26 for more information.

Summary of Contents for 2408





























Reviews: