background image

 

 

Tempest Lantern 

Owner’s Manual 

Natural Gas

 (sku#

 

94900746)  -  

Propane

 (sku# 94900756) 

Tested and 
listed by

 

 

Portland 
OR

 

ANSI Z21.97-2017 / CSA 2.41-2017, CSA 2.17-2017 

Outdoor Decorative Gas Appliances 

Report # 0028GM083S 

 

WARNING:  For Outdoor Use Only.   Installation and service must be performed by a 
qualified installer, service agency or the gas supplier.  

 

 

WARNING:  If the information in this manual is not followed exactly, a fire or explosion 
may result causing property damage, personal injury, or loss of life. 

 

 

WARNING:  Do not store or use gasoline, or other flammable vapors and liquids, in the 
vicinity of this or any other appliance. 
An LP-cylinder not connected for use shall not be stored in the vicinity of this or any other 
appliance. 

 

DANGER:  FIRE OR EXPLOSION HAZARD

 

If you smell gas: 

 

Shut off gas to the appliance. 

 

Extinguish any open flame. 

 

If odor continues, leave the area immediately. 

 

After leaving the area, call your gas supplier or fire department. 

Failure to follow these instructions could result in fire or explosion, which could cause 
property damage, personal injury, or death. 

 

 

 

CARBON MONOXIDE 

HAZARD 

 

This appliance can produce 
carbon monoxide which has 
no odor. 

 

Using it in an enclosed 
space can kill you. 

 

Never use this appliance in 
an enclosed space such as a 
camper, tent, car or home. 

 

Hot glass will 

cause burns. 

 

Do not touch 
glass until 
cooled. 

 

Never allow 
childern to 
touch glass.

 

 

 

INSTALLER: Leave this manual with the appliance. 
CONSUMER: Retain this manual for future reference. 

$10.00 

 Copyright 2020, T.I.     

 

Part # 100-01535

 

 

Summary of Contents for 94900746





















Reviews: