manualshive.com logo in svg

TransTank GlidePath, Operator'S Handbook Manual

Share
Download
TransTank GlidePath Operator'S Handbook Manual Download Page 4

1800  816  277

www.tti.com.au

4

Product HandBook

GlidePath

™

General Safety Instructions 

1.  This unit is designed and manufactured solely for the purpose of carrying and spraying herbicides and 

pesticides.  Under no circumstances should it be used for any other purpose.  It must never be used for 
transporting fuel.

2.  Only authorised and trained personnel are to operate this equipment.  Operators must have read and fully 

understood this manual before operating the GlidePath unit.

3.  Do not operate the GlidePath anywhere near bystanders, livestock, watercourses or any non-targeted 

vegetation that may be in danger from spray drift contamination.

4.  Wind direction and speed must be taken into account, as windy conditions may endanger the operator or 

damage to adjacent non-target vegetation.  Avoid spraying on hot and sunny days or when wind speed 
exceeds 6.5km/h.

5.  Do not operate this equipment while under the influence of alcohol or any drugs that could impair your 

capabilities in any way.

6.  PPE appropriate to the chemicals being used must be worn at all times when operating the GlidePath.  

As a minimum, the PPE should include coveralls, gloves and boots.  A face shield and PVC apron are 
recommended depending on the task.  It is recommended that the following documents should be read 
and understood by the operator:

•  Australian Standard for Chemical protective clothing AS3765
•  Australian Standard for Respiratory protection devices AS1715

7.  Ensure the capacity of the tow vehicle is suitable for the loaded mass of the GlidePath.  Refer to the 

vehicle’s operator manual for safe working loads, correct securing points and relevant safety instructions.  
Do not exceed the carrying and braking capacity as specified by the vehicle manufacturer.  As a guide, one 
litre of water weights one kilogram (kg), therefore a full 1,000 litre GlidePath will weigh in excess of 1,200kg 
without options.

8.  Care should be taken at all times, particularly when operating on rough or steep terrain. Drivers should be 

aware of fluid surge affecting the vehicle’s centre of gravity.

Safety 

This manual is intended for use by personnel experienced in the use of this and similar equipment.  Read 
and understand this manual before attempting to operate or perform routine maintenance on this equipment.  
Your safety is of prime priority. 

A 

WARNING

 highlights an essential operating or maintenance procedure, 

practice, condition or statement, which, if not strictly observed, could result 
in injury or death of personnel, or long-term health hazards. 

A CAUTION highlights an essential operating or maintenance procedure, 
practice, condition or statement, which, if not observed, could result in 
damage or destruction of equipment. 

A NOTE highlights or clarifies an essential systems description, operating or 
maintenance procedure, condition or statement. 

Summary of Contents for GlidePath





























Reviews:

No comments

Brands by name

Popular brands

Load more brands