Transmitter Solutions Reign XRE-100 Manual Download Page 11

The warranty period of this product is 24 months, beginning from the manufacturing date.  During this period, if the 
product does not operate correctly, due to a defective component, the product will be repaired or replaced at the sole 
discretion of Transmitter Solutions.  This warranty does not extend to the product casing which can be damaged by 
conditions outside of the control of Transmitter Solutions.

EXCEPT AS SET FORTH ABOVE, TRANSMITTER SOLUTIONS MAKES NO WARRANTIES REGARDING THE GOODS, EXPRESS OR IMPLIED, 
INCLUDING WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.  BUYER MAKES NO RELIANCE ON 
ANY REPRESENTATION OF TRANSMITTER SOLUTIONS, EXPRESS OR IMPLIED, WITH REGARD TO THE GOODS AND ACCEPTS THEM 
“AS-IS/WHERE-IS”. TRANSMITTER SOLUTIONS SELLS THE GOODS TO BUYER ON CONDITION THAT TRANSMITTER SOLUTIONS WILL HAVE NO 
LIABILITY OF ANY KIND AS A RESULT OF THE SALE.  BUYER AGREES THAT TRANSMITTER SOLUTIONS SHALL HAVE NO LIABILITY FOR 
DAMAGES OF ANY KIND, WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING INJURIES TO PERSONS OR PROPER-
TY, TO BUYER, ITS EMPLOYEES OR AGENTS, AS A RESULT OF THE SALE.  BUYER ALSO AGREES TO HOLD TRANSMITTER SOLUTIONS 
HARMLESS FROM ANY CLAIMS BUYER, OR ANY THIRD PARTY, MAY HAVE AS A RESULT OF BUYER’S USE OR DISPOSAL OF THE GOODS. 
BUYER HAS READ THIS DISCLAIMER AND AGREES WITH ITS TERMS IN CONSIDERATION OF RECEIVING THE GOODS.

WARRANTY

11

Summary of Contents for Reign XRE-100













Reviews: