CDFTFxxxx-10x
8
24-hour Technical Support:
1-800-260-1312
-- International:
00-1-952-941-7600
Technical Specifications
For use with Transition Networks Model CDFTFxxxx-10x or equivalent.
Standards
IEEE 802.3™
Data Rate
10 Mb/s
Dimensions
3.4" x 0.86" x 5.0" (86 x 22 x 127 mm)
Weight
3 oz (91 g) (approximate)
Power Consumption
6.8 watts
MTBF
484,000 hours (MIL217F2 V5.0) (MIL-HDBK-217F)
1,359,000 hours (Bellcore7 V5.0)
Environment
Tmra*:
0 to 60°C (32 to 140°F )
Storage Temp:
-20 to 85°C (-4 to 185°F)
Humidity:
5 to 95%, non condensing
Altitude:
0 to 10,000 feet
Warranty
Lifetime
*Manufacturer’s rated ambient temperature: Tmra range for this slide-in-module
depends on the physical characteristics and the installation configuration of the
Transition Networks PointSystem™ chassis in which this slide-in-module will be
installed.
Product is certified by the manufacturer to comply with DHHS Rule 21/CFR,
Subchapter J applicable at the date of manufacture.
CAUTION:
Visible and invisible laser radiation when open. Do not stare into
the beam or view directly with optical instruments.
CAUTION:
Use of controls, adjustments or the performance of procedures other
than those specified herein may result in hazardous radiation exposure.
Operation
-- Continued
SNMP
Use SNMP at an attached terminal or at a remote location to monitor the
media converter by monitoring:
•
Media converter power.
•
Copper link status on media converter #1.
•
Fiber link status on media converter #1.
•
Activity on media converter #1.
•
Copper link status on media converter #1.
•
Fiber link status on media converter #1.
•
Activity on media converter #1.
Also, use SNMP to enter network commands that:
•
Enable/disable AutoCross.
See the on-line documentation that comes with Transition Networks
FocalPoint™
software for commands and usage at www.transition.com.
9
-- Click the
“Transition Now”
link for a live Web chat.
Cable Specifications
The physical characteristics must meet or exceed IEEE 802.3™ specifications.
Telco Copper Cable
Maximum cable distance = 60 m (197 ft.)
Category 5:
(minimum requirement)
Gauge
24 to 22 AWG
Attenuation
22.0 dB /100m @ 100 MHz
(See page 4 for the Telco cable signal distribution over the 50-pin
connector at the back of the CPSMC1850-150
PointSystem™
chassis.)
Fiber Cable
Bit Error Rate:
<10-9
Single mode fiber (recommended):
9 µm
Multimode fiber (recommended):
62.5/125 µm
Multimode fiber (optional):
100/140, 85/140, 50/125 µm
CDFTF1111-100
1300 nm multimode
CDFTF1313-100
1300 nm multimode
Fiber Optic Transmitter Power:
min: -19.0 dBm
max: -14.0 dBm
Fiber Optic Receiver Sensitivity:
min: -30.0 dBm
max: -14.0 dBm
Link Budget:
11.0 dB
CDFTF1414-100
1310 nm single mode
Fiber-optic Transmitter Power:
min: -15.0 dBm
max: -8.0 dBm
Fiber-optic Receiver Sensitivity:
min: -31.0 dBm
max: -8.0 dBm
Link Budget:
16.0 dB
CDFTF1515-100
1310 nm single mode
Fiber-optic Transmitter Power:
min: -8.0 dBm
max: -2.0 dBm
Fiber-optic Receiver Sensitivity:
min: -34.0 dBm
max: -7.0 dBm
Link Budget:
26.0 dB
CDFTF1616-100
1310 nm single mode
CDFTF1717-100
1550 nm single mode
Fiber-optic Transmitter Power:
min: -5.0 dBm
max: 0.0 dBm
Fiber-optic Receiver Sensitivity:
min: -34.0 dBm
max: -7.0 dBm
Link Budget:
29.0 dB
CDFTF2929-100
1310 nm (TX)/1550 nm (RX) simplex
CDFTF2929-101
1550 nm (TX)/1310 nm (RX) simplex
Fiber-optic Transmitter Power:
min: -13.0 dBm
max: -6.0 dBm
Fiber-optic Receiver Sensitivity:
min: -32.0 dBm
max: -3.0 dBm
Link Budget:
19.0 dB
CDFTF2929-102
1310 nm (TX)/1550 nm (RX) simplex
CDFTF2929-103
1550 nm (TX)/1310 nm (RX) simplex
Fiber-optic Transmitter Power:
min: -8.0 dBm
max: -3.0 dBm
Fiber-optic Receiver Sensitivity:
min: -33.0 dBm
max: -3.0 dBm
Link Budget:
25.0 dB
The fiber optic transmitters on this device meets Class I Laser safety
requirements per IEC-825/CDRH standards and complies with 21
CFR1040.10 and 21CFR1040.11.
