background image

                                                              Red LED 

                                                                   

 

 

 

 

 

In normal weigh mode, the LED is flickering: the flicker frequency is 

almost 2Hz in zero, the flicker frequency is almost 1Hz in other 

weight; in setting mode, the LED lighten or black out. 

 

4.3 TI-1500VC Calibration 

 

Note: Every TI-1500VC has Factory Reset (F21) when it out of 

the factory. The 4-20mA and 0-10V has been adjusted, so the 

user shouldn’t repeat F21, otherwise the analog output should 

been adjusted again. 

 

4.3.1 Calibration 

Example: The system result: 3000 x 0.1kg=300kg 

 

(1) Graduations: Enter setting mode, the display show [F1].  

Press “

” key enter, the display show [xxxxx], if now the value 

is [3000], press “

”, back to the main menu. Otherwise, press 

” or “

” key, until the display show [3000], press “

SET

” to 

save the change. Then press “

”, back to the main menu, the 

display show [F1] again. 

(2) Display Divisions: Press “

” key, until the display show [F9].  

Press “

” key enter, the display show [div x], if now the value is 

[div 1], press “

”, back to the main menu. Otherwise, press 

” or “

” key, until the display show [div 1], press “

SET

” to   

-11- 

save the change. Then press “

”, back to the main menu, the 

display show [F9] again. 

(3) Decimal Point: Press “

” key, until the display show [F10].  

Press “

” key enter, the display show [xxx], if now the value is 

[0.0], press “

”, back to the main menu. Otherwise, press “

” 

or “

” key, until the display show [0.0], press “

SET

” to save the 

change. Then press “

”, back to the main menu, the display 

show [F10] again. 

(4) Zero Calibration: Press “

” key, until the display show [F16]. 

Make sure there are no test weights on the platform, press “

” 

key enter, the display show the present zero A/D count. When 

the stabile annunciator turns on, press “

” key to set zero point, 

then press “

SET

” key to save the zero value. 

(5)  Span Calibration: Press “

” key, until the display show [F17]. 

Place the full capacity test weight on the platform, press “

” 

key enter, the display show flash [    0], press “

” key 3 times, 

the display show [    0000], press “

” input [3], now the display 

show [3000], it’s equal to the test weight. When the stabile 

annunciator turns on, press “

SET

” key to save the span value. 

 

Now finishing the calibration, turn off the system. Then turn it on 

again, the system back to the normal weigh mode. 

 

4.3.2 Adjust the Zero Track Band (F3) 

 

Zero Track Band means in stabile state the system will 

automatically zero within the setting zero track range. The system’s 

default zero track value is 1d. If the system use in large wind 

environment or there will be some residues leave on the platform 

every weight, the zero track parameter should be 

-12- 

Summary of Contents for TI-1500VC












Reviews: