background image

AMS-SVX03A-EN 

17

Controller instruction

Remote controller front appearance and function buttons are as followings:

On/Off

Press this key to control On or Off of air conditioner (only the clock 
is displayed in Off state)

Temperature 
setting

Press the key 

 or 

 to increase or decrease current set 

temperature. Range of settings: 16

ņ

-30

ņ

, setting a temperature 

in the Fan mode is invalid!

Mode (for 
cooling only)

Press this key to switch among modes in the following order: 
Cooling 

ŚĘ

Dry

ęŚ

 Fan 

ŚĘ

Heating

ęŚĘ

Auto Cooling/Heating

ę

.

Fan

Press this key to switch among speeds in the following order: 

Ę

Auto

ęŚ

 Low 

Ś

 Medium 

Ś

 High, there is no Auto mode in the 

Fan mode and no Low mode in the Dry mode.

Swing

Press this key once to enable the Swing function, press it again to 
disable this function.

Light

Only valid in ON state. Invalid in OFF state: when the unit is turned 
off, the light is off.
When the unit is turned on, the light is on by default. Press this 
button again the light is off, making a cycle.

Sleep

Press this key once to enable the Sleep function, press it again to 
disable this function.

Electric heating

Press this key once to enable the electric heating, press it again 
to disable this function; the Auto Auxiliary Heating is enabled by 
default. This wall-mounted unit is without electric heating.

Priority

Press this key once to enable the Priority and press it again to 
disable this function.

Quick Cooling/
Heating

If current mode is Cooling, press this key to enter the Quick Cooling 
mode; if current mode is Heating, press the key to enter the Quick 
Heating mode.

Auto On/
Off time and 
system time 
setting

Auto On/Off time and system time setting:
Press the key "Timer" to enter the Auto On time setting. Here, 

Đ

NO

đ

 

is illuminated and fl ashes, press 

 or 

Ř

 to set Auto On time and 

the time will increase or decrease by 10min; if there is no action 
within 3sec, "NO" will stop fl ashing and the system enters Auto 
On automatically. Press "Timer" key again to enter Auto Off time 
setting, here "OFF" is illuminated and fl ashes, press 

 or 

Ř

 to set 

Auto Off time and the time will increase or decrease by 10min; if 
there is no action within 3sec, "OFF" stops fl ashing and the system 
enters Auto Off automatically. Press "Timer" key once again to 
enter the System Time setting, here the system time fl ashes, press 

 or 

Ř

 to set the time and the time will increase or decrease by 

1min; if there is no action within 3s, the system will go to the time 
screen automatically. The fourth pressing of "Timer" key will exit 
from all the time settings. 
Note: If in the time setting, the time set by pressing 

 or 

Ř

 is 

beyond 12:00, then "AM" and "PM" will alternate.

Enable auto ON/OFF

Press 

Đ

TIMER

đ

 and 

Đ

Quick cooling/heating

đ

 

button simultaneously to enter auto ON.
Press 

Đ

TIMER

đ

 and 

Đ

Quick cooling/heating

đ

 

button again to enter auto OFF.
Press 

Đ

TIMER

đ

 and 

Đ

Quick cooling/heating

đ

 

button once again to enter auto ON/OFF.
The fourth pressing of 

Đ

TIMER

đ

 and 

Đ

Quick 

cooling/heating

đ

 button will clear all.

7,0(5

Summary of Contents for MW(C)W509
























Reviews: