background image

4

Section 2. Unit Design

2.1 Cabinet Penetration

Screws can be drilled 

into bottom of unit. 

(1/2” max. screw length)

(Typical all sides)

Screws, saw cuts, and 

other penetrations 

are allowed in the 

blower section for 

installation of Side 

Return Kit. 

(Typical both sides)

Screws are allowed up to 3- 3/4” 

from the top of the cabinet 

(heater compartment).

(Typical both sides)

Screws for flange kit

attachment are allowed

along the interior of 

the cabinet (see arrows)

(Typical all sides)

No penetrations 

allowed.

(Typical all sides)

Screws allowed only in 

the first 3/4” of front 

bottom of unit (in cross 

member)

Important: 

Due to the unique design of this unit, 

which allows the electrical wiring to be routed within 
the insulation, do not screw, cut, or otherwise punc-
ture the unit cabinet in any location other than the 
ones illustrated.

Important: 

Under no conditions should metal strap-

ping be attached to the unit to be used as support 
mechanisms for carrying or suspension purposes.

2.2 Panel Removal

The unit contains four (4) access panels: Blower/Fil-
ter, Coil, Line Set, and Heater.

The Blower/Filter panel is removed using 1/4 turn 
thumb screws.

1.    Turn thumb screws on Blower/Filter panel.
2.   Pull top of panel out, away from cabinet.
3.   Lift panel up out of channel.
4.   Set aside.

Summary of Contents for GAM5 Series









































Reviews: