background image

18-CD29D1-3

7

Installer’s Guide

UPFLO

W

FURNA

CE

CASED

COIL

SCREWS

(BOTH SIDES)

STANDOFFS

(BOTH SIDES)

STANDOFFS (4)

DRILL SCREWS (4)

FOR VERTICAL

INSTALLATIONS:

1

HORIZONTAL INSTALLATION

The coil and furnace must be fully supported when used
in the horizontal position. It is always recommended
that an auxiliary drain pan be installed under a horizon-
tally installed evaporator coil or 95% gas furnace. Con-
nect the auxiliary drain line to a separate drain line (no
trap is needed in this line).
Three brackets (with screws) are included with down-
flow furnaces for installation to stabilize and secure the
furnace and TXC cased coil in the 

horizontal posi-

tion

. See Figure 4.

IMPORTANT:
The 2/4TXC cased coil must be placed downstream of the
furnace.  In horizontal installations, the apex of the coil
may point either toward or away from the furnace.  See
the 2/4TXC coil Installer's Guide for more details.

The cased coil is secured to the furnace and both the
furnace 

and

 the cased coil must be properly supported.

The brackets mount using the rear screws on the coil
case and use the screws provided to secure the bracket
to the furnace. The remaining bracket is placed as close
to center as possible (horizontally) between the coil case
front and the furnace bottom channel (for downflow/
horizontal furnace). Use four of the screws provided to
secure the bracket. The upflow furnace, converted to
horizontal, aligns and attaches the TXC coil as in Fig-
ure 1. However, the coil requires additional support.

UPFLOW INSTALLATION

Standoffs and screws (See Figure 1) are included with
the cased coils for attachment to the furnace. There are
clearance alignment holes near the bottom of the coil
wrapper. Drill screws are used to engage the furnace
top flanges. The standoff is inserted into the cabinet
alignment hole. The drill screws are inserted through
the standoffs then screwed into the furnace flange.

The coil is always placed downstream of the furnace air-
flow.

DOWNFLOW INSTALLATIONS

WARNING

!

FIRE HAZARD
Do NOT install the furnace directly on carpeting, tile or
other combustible material other than wood flooring.
For vertical downflow application, subbase (BAYBASE-
205) must be used between the furnace and combus-
tible flooring. When the downflow furnace is installed
vertically with a cased coil, a subbase is not required.

Required floor opening:

SUBBASE CROSS SECTION

TABLE 1

CABINET

WIDTH

RETURN

DUCT WIDTH

FLOOR OPENING PLENUM OPENING

"A"

"B"

"C"

"D"

17-1/2"

16-1/4"

16-5/8"

20-1/8"

15-5/8"

19-3/8"

21"

19-3/4"

20-1/8"

20-1/8"

19-1/8"

19-3/8"

24-1/2"

23-1/4"

23-5/8"

20-1/8"

22-5/8"

19-3/8"

2

1234567890123456789012345678901212345678901234567

1234567890123456789012345678901212345678901234567

1234567890123456789012345678901212345678901234567

1234567890123456789012345678901212345678901234567

1234567890123456789012345678901212345678901234567

1234567890123456789012345678901212345678901234567

1234567890123456789012345678901212345678901234567

1234567890123456789012345678901212345678901234567

1234567890123456789012345678901212345678901234567

1234567890123456789012345678901212345678901234567

1234567890123456789012345678901212345678901234567

1234567890123456789012345678901212345678901234567

1234567890123456789012345678901212345678901234567

1234567890123456789012345678901212345678901234567

1234567890123456789012345678901212345678901234567

1234567890123456789012345678901212345678901234567

1234567890123456789012345678901212345678901234567

1234567890123456789012345678901212345678901234567

1234567890123456789012345678901212345678901234567

1234567890123456789012345678901212345678901234567

1234567890123456789012345678901212345678901234567

FURNACE

FRONT

A (width)

B (depth)

C

D

3

CASED COIL CONNECTION

BRACKET FOR DOWNFLOW

FURNACE IN HORIZONTAL

DOWNFLOW ONLY

4

The furnace may be installed in an attic or crawl space
in the horizontal position by placing the furnace 

on the

left side

 (as viewed from the front in the vertical posi-

tion). The horizontal furnace installation in an attic
should be on a service platform large enough to allow
for proper clearances on all sides and service access to
the front of the furnace (See Figure 3 & Clearance
Table 1). Line contact is only permissible between lines
formed by intersections of the top and two sides of the
furnace casing and building joists, studs, or framing.

Summary of Contents for *DH1B040A9241A









































Reviews: