Trane Arctic Manhattan Gen II Installation, Operation And Maintenance Manual Download Page 70 | Manualshive

Page: 70 / 88

background image

70

ARTC-SVX001B-EN

Code (hex)

Fault / Aux. code

Cause

What to do

5691

Measurement circuit ADC

Measurement circuit fault.

Contact your local ABB
representative.

5692

PU board powerfail

Power unit power supply failure.

Contact your local ABB
representative.

5693

Measurement circuit DFF

Measurement circuit fault.

Contact your local ABB
representative.

5696

PU state feedback

State feedback from output phases
does not match control signals.

Contact your local ABB
representative.

5697

Charging feedback

Charging feedback signal missing.

Check the feedback signal coming
from the charging system

6181

FPGA version incompatible

Firmware and FPGA versions are
incompatible.

Reboot the control unit (using
parameter

96.08 Control board boot

) or by

cycling power. If the problem
persists, contact your local ABB
representative

6306

FBA A mapping file

Fieldbus adapter A mapping file read
error.

Contact your local ABB
representative.

6481

Task overload

Internal fault.

Reboot the control unit (using
parameter

96.08 Control board boot

) or by

cycling power. If the problem
persists, contact your local ABB
representative

6487

Stack overflow

Internal fault.

Reboot the control unit (using
parameter

96.08 Control board boot

) or by

cycling power. If the problem
persists, contact your local ABB
representative

64A1

Internal file load

File read error.

Reboot the control unit (using
parameter

96.08 Control board boot

) or by

cycling power. If the problem
persists, contact your local ABB
representative

64B2

User set fault

Loading of user parameter set failed
because
• requested set does not exist
• set is not compatible with control
program
• drive was switched off during
loading.

Ensure that a valid user parameter
set exists. Reload if uncertain.

64E1

Kernel overload

Operating system error.

Reboot the control unit (using
parameter

96.08 Control board boot

) or by

cycling power. If the problem
persists, contact your local ABB
representative

6581

Parameter system

Parameter load or save failed.

Try forcing a save using parameter

96.07 Parameter save manually

.

Retry.

65A1

FBA A parameter conflict

The drive does not have a
functionality requested by PLC, or
requested functionality has not been
activated.

Check PLC programming.
Check settings of parameter groups

50 Fieldbus adapter (FBA)

and

51

FBA A settings

.

6681

EFB comm loss Programmable fault:

58.14 Communication loss action

Communication break in embedded
fieldbus (EFB) communication.

Check the status of the fieldbus
master (online/offline/error etc.).
Check cable connections to the
EIA-485/X5 terminals 29, 30 and 31
on the control unit.

«
...
68
69
70
71
72
...
»

Summary of Contents for Arctic Manhattan Gen II

























































































Reviews:

No comments

Related manuals for Arctic Manhattan Gen II

Brand: Johnson Controls Pages: 334

Brand: LEMKEN Pages: 26

Brand: Worx Pages: 24

Brand: Elkay Pages: 2

Brand: Carrier Pages: 68

Brand: Carrier Pages: 8

Brand: Carrier Pages: 24

Brand: Carrier Pages: 116

Brand: Texas Pages: 20

Brand: Texas Pages: 16

Brand: Texas Pages: 24

Brand: Texas Pages: 26

$Texas EL-TEX 1400 User Manual preview$

Brand: Texas Pages: 34

Brand: Texas Pages: 32

Brand: Texas Pages: 46

Brand: Carrier Pages: 28

Brand: Haussmann Pages: 24

Brand: Cub Cadet Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands