Triad OnWall Nano LCR 3.0 w/ EasyMount Bracket - Quick Start Guide
2014.
7.23
Specifications
Applicable Models Dimensions
Inches / cm
OnWall Nano LCR 3.0 44x3.25x1.6; 111.7x8.2x4.1
Frequency Response
+/-3dB, 2pi*
*
150 Hz - 20 kHz
Sensitivity
Rec Amp Pwr
2.83v, 1m
Per Channel
8
4
dB
75 - 125Watts
Rec Sub Xover
175Hz
/ 200Hz**
Weight lbs/kg
8.0/ 3.6
*2 pi Frequency Response shows performance when mounted on or against a wall or other large surface. When mounted in free air (4pi), e.g. on a swing arm TV bracket pulled out from the wall,
the bass will be less extended and Sub Crossover frequencies should be raised at least 10 Hz (to 200Hz for Nano).
Additional Info
Triad's EasyMount wall bracket, included with each speaker, is quick & easy to install, adds no depth, and allows up to .5 inch (12.7mm) horizontal and vertical adjustments for
leveling or aligning.
North American Limited Warranty
Triad speakers are warranted to be free from defects in manufacturing and workmanship (10) years when operated under normal conditions. Should any such defects occur within
the warranty period call Triad Service at 1-877-264-6315 for an RA (Return Authorization) number. Return the product in intact factory packaging with RA number clearly visible on
outside of box and proof & date of purchase inside to:
Triad Speakers Inc., 15835 NE Cameron Blvd., Portland, Oregon 97230 USA
Triad is not responsible for any shipping damage coming in to Triad. If you do not have intact factory packaging, contact your dealer or Triad Service for purchase. At our discretion
we will repair or replace the product and return it free of charge. International customers should contact their dealer for service. This limited warranty is extended only to Triad
products and is expressly in lieu of all other warranties expressed or implied.
Unpacking / Contents
Speaker
(OnWall Nano LCR 3.0)
Template
Grill
EasyMount Bracket and Hardware
(anchors
& key,
screws, mounting posts, and knobs).
TriadSpeakers.com • Sales: 1800-666-6316
OnWall Speaker
- Product Info & Warranty -
Page 1
Hanger B (x1)
1.125" OD x 0.26"ID
Plastic Spacer (x14)
5/32 Hex Key (x1)
Hanger A (x1)
1/4-20 screw 1.25" long (x2)
1/4-20 screw 0.75" long (x2)
1/4-20 screw0.50" long (x2)
1.0" OD X 0.28" ID
Metal Flat Washer (x2)
1.125" OD x 0.32"
Metal Offset Spacer (x2)
1/4-20 screw 1.00" long (x2)
OnWall Nano Specific Parts with TV Brackets
TV Brackets (X2)
Level & pin template to wall. Outline
wire hole and screw holes for 2 mounting
posts - or 4 with streched sound-bars
longer than 66"/1676.4 mm. Always
orient posts vertically.
Cut wire hole; install anchors if there
are no studs;
once anchors are in the
drywall, pop them open with the
included key. Then screw mounting
posts to wall using all the anchors &
screws provided. Mounting posts
should always be mounted vertically
(portrait) for strength.
A
Pull speaker wire through wire hole;
Connect all 3 pairs of speaker wires to the
Phoenix connector.
Check for shorts &
correct polarity.
Tighten screws; then
insert Phoenix male into the speaker
enclosure’s Phoenix female.
Mount speaker on posts; loosely
tighten knobs. Level or align +/- 1/4”
(6.35mm), then tighten.
To attach the grill
e
, start at one end:
1): With grill
e
overlapping the speaker
by approx 1 inch, seat this end of the
grill
e
onto the enclosure.
2): Slide the near end of the grill
e
inward
so its endcap butts up to the enclosure.
3): Snug the grill
e
along top & bottom edges
of the enclosure until the far end snaps in.
C
B
D
E
Horizontal Installation
On Stud
Off Stud
Connector (X1)
1) 2)
1)
2)
3)
Overhead View
Anchor
Key
x1
* For safety, superstretched models longer than 66 inches
(1676.4mm) include 4 sets of EasyMount Brackets &
Hardware. If your speaker includes 4 sets, use them
all as per instructions on page 2.
x2*
x2*
Nominal
Impedance
6 ohms
EZ Bracket
Post length
1 inch
OnWall speakers
stretched larger
than 66” require
4 EZ Mounts
5/16"
8mm
