background image

1

SKIRTED SERIES    

INSTALLATION INSTRUCTIONS 

WHIRLPOOL MODELS: 

SW3060LH, SW3060RH, SW3260LH, SW3260RH, SW3660LH, SW3660RH, 
SW4260LH, SW4260RH 

SOAKING TUB MODELS:  ST3060LH, ST3060RH, ST3260LH, ST3260RH, ST3660LH, ST3660RH, 

ST4260LH, SW4260RH 

                              

NOT SUITABLE FOR FIELD INSTALLED HEATER 

READ AND FOLLOW ALL INSTRUCTIONS 

INSPECT THIS SHIPMENT FOR POSSIBLE TRANSIT DAMAGE 

This unit has been factory tested for leaks and workmanship.  Damage may occur during shipping or in the ac-
tual installation.  It is required that the unit be field tested prior to final installation.  Failure to do so may result 
in voiding the manufacturer’s warranty.  Under no circumstances will the manufacturer be liable for any damage 
due to leaks by the unit. 

HOW TO WATER TEST  

Fill the unit with water to a level one inch above the jets and visually inspect all fittings for any static leaks.  If 
any leaks are noticed, contact your dealer or the factory at once.  Do not install the unit until the leaks are re-
paired. 

7612 Drag Strip Road – Fairview, TN 37062 – 615/799-8300 – www.tradewindinc.com 

Summary of Contents for ST3060LH











Reviews: