background image

14

APPENDIX – “CE” DECLARATION OF CONFORMITY

"CE" Declaration of Conformity 

according to annex II. 1. A of the European Machinery Directive 2006/42/EC 

Temporary suspended platform "TSP" 

Model "SUBITO" 

(no serial number) 

The manufacturer:  Tractel Secalt S.A.

 (a TRACTEL

®

 Group company)

3, rue du Fort Dumoulin 

P.O. box 1113, L-1011 Luxembourg 

Tel. (352) 43 42 42-1 * Fax (352) 43 42 42-200 

declares that the machine is in accordance with the model having received the CE type 

approval  No.  0398/TYP/760S/0100/06/10,

  confirming  the  conformity  to  the  "machinery 

directive" ( No. 2006/42/EC ) delivered by the notified body: 

APAVE Italia Cpm

, Via Artigiani 63, I-25040 BIENNO (BS), Italy (No. 0398) 

The machine also complies with the following harmonized standards:

 

- EN ISO 12100-1-1/A1-2-2/A1, EN 1808+A1

and with the other standards, recommendations and following specifications: 

- DIN 15020

NOTE: The suspension points are not scope of delivery 

Responsible for the documentation:

 Jörg Thierer; see company address above. 

Authorised signature: 

Name: 

Function: 

Place and date of signature: 

Jörg THIERER 

General Manager 

Luxembourg, 

xx

/

xx

/201

8

 

Signature: 

- MC1452-SUBITO_6FR-EN-D-IT-ES-NL  0

7

/201

8

Summary of Contents for subito















Reviews: