Trackunit TU600-x Short Manual Download

Page: 2 / 17

TU600-x

Short Guide TU600-x v0.2, January 2020, ©Trackunit 2020

Index

Practical Advice .......................................................................................... 3

Machine and vehicle guidelines for correct wiring ....................................... 4

Installation example .................................................................................... 5

Functionality check: LED on the unit ........................................................... 6

Installation check and update using “Verify my Trackunit” .......................... 7

Input filtering (INFILT) ................................................................................. 8

CAN bus termination resistor ...................................................................... 9

Troubleshooting ........................................................................................ 10

Product specifications ............................................................................... 11

Temperature range ................................................................................... 12

Mechanical specifications ......................................................................... 12

Regulatory information and precautions.................................................... 13

Approvals and Certifications ..................................................................... 15

Summary of Contents for TU600-x


















Search results

Summary of Contents for TU600-x

Reviews:

Related manuals for TU600-x

Brands by name

Popular brands

Trackunit TU600-x, Short Manual

Search results

Summary of Contents for TU600-x

Reviews:

Related manuals for TU600-x

Brands by name

Popular brands