background image

11.15 MONITOR

Press ENT into figure 1 (from left), don't touch neutral position of steering and 

throttle, press ENT button, the neutral position has calibrated and into Figure 2, 

moving the direction of steering to the end-point maximum position, and return 

back neutral position not move. Then put throttle trigger to end-points of two 

sides and return back neutral position not move. Movement no sequence, no 

numbers requirement, multiple or first mover throttle has no effect, the premise is 

each movement must be to the end-point position. Then press ENT into figure 3, 

showing channel calibration done, press EXIT to save and exit.

This function is to display the channel running status. And to check whether the 

calibration of function 11-13 channels ADJ  is correct or wrong. 

The output pulse is about 1000US - 2000US. 

The median point of the pulse is about 1500US. 

First passed function 11-12 RESET  re-set system . Viewing neutral parameters. 

ST display about is 1500US (allow showing numbers a slight fluctuation)

TH display about is 1500US (allow showing numbers a slight fluctuation)

Pulling the throttle trigger to two ends display the value about 1000US -2000US.

TH output pulse is normal. 

Turn the steering to the left and right ends, by adjusting the D/R knob, the value 

displayed about 1000US-2000US.  ST output pulse is normal 

AUX displayed value is at around 1000US - 2000US end-point value. 

Note: 1. Allowing showing numbers a slight fluctuation. It is normal. 

          2. If these values are displayed above. Please do not run 11 – 13 function.

11.16 SPEED

This function is to test wheel speed by light-sensor. It is important to note that the 

use of light-sensor need to outdoors with bright areas which makes the test result 

more accurate. And you could not install light-sensor in the shadow or backlight. 

It also requires specification of the impeller blades are organized distribution, 

standardized  impeller blades shown in the below left picture.

How to install.

Light-sensor should be installed verticality to the wheel impeller blades ( Princi-

ple of operation: light sensor vertical light is blocked periodically in order to 

calculate the wheel speed), the installation distance in accordance with the best 

lighting effects. The vertical best distance (1CM-4CM) . If it is five impeller 

blades, setting Blade sum by pr / - keys to five. The largest selection of 

impeller blade support 12. This supports high-speed rotating speed, low speed 

test is not supported, if it is two pieces of the impeller blades required minimum 

rotate speed achieve 480RPM. 12 impeller blades max support testing rotate 

speed up to 50,000RPM.

At the same time it can remember the max speed at the whole processing. Tx 

from turn on to switch off is a process. Switch off  the Tx the Max Speed will 

clear to zero.

NOTES

: When the supply voltage of the receiver is lower than 5.2V, the supply 

voltage is not enough to the light sensing probe, the test of speed will be not 

accurate, while different fixed number will be shown on screen time to time.

12. Installing battery

   

 

LIGHT SENSOR

BEAM

1

2

3

The transmitter battery standard installed use four dry batteries or four Ni-MH 

rechargeable batteries. Because of the special design of the battery box, so the 

battery cover makes installation a little tight, you can help other artifacts gently 

force open the battery cover.

The process of installing the battery, if the battery box is removed, put it back 

again, do not suppress the battery box power line, otherwise cause the battery 

cover is not easy to close.

For customers DIY the battery, transmitter maximum support 8.6V voltage, so 

using 2S Li-Po battery should pay attention to the positive and negative pole 

correct connect JST connector base. Especially the charge must be used balance 

charger, so as to ensure the relative safety of charge

17

16

Summary of Contents for TS3T












Reviews: