background image

 

10 

 

 

 

 

 

 

 

CAUTION!!!!
SPINNING BLADE

OPERATING PROCEDURE 

 

 

 

BEFORE STARTING, 

follow the engine manufacturer’s instructions in preparing engine for  

 

      operation. Never fill fuel tank indoors, with engine running or while engine is hot.  

Do Not smoke    

 

      while filling tank! 

 

 

 

 1.  Inspect area to be vacuumed and pickup all harmful objects and litter. Rocks and other harmful  

 

 

      debris can do serious damage to vacuum assembly and cause bodily injury. 

 

 

 2.  For best vacuuming results operate tractor at manufacturer's recommended speed for best cutting. If grass 

 

     is high, mow first and vacuum on the second pass. 

 

  

 3. Your vcuum is preset to run at approximately 3200-RPM (380), 3800-RPM (385), at no load. Do not slow 

 

      down engine.  

 

  

4.  

SHUT OFF ENGINE TO UNLOAD

 

         5.   When operating tractor on slope or grade, exercise extreme caution. Do not cut across grade or  
 

      slope. Mow directly up and down hills.  

 

 

6.   Periodically check all fasteners for tightness. 

 

  

7.   Listen for unusual vibration of engine or air turbine. If excessive vibration is present, STOP engine  

 

      and check for damage to turbine fan. 

 

         8.   Always shut off tractor engine and vacuum engine before servicing. 

 

         9.   Replace deflector shield when discharge chute is removed. 

 

       10.  When removing clogs, 

SHUT OFF ALL ENGINES and wait for all moving part to come to a      

 

     complete stop!  Failure to do so can cause serious bodily injury! 

 

       

11.  Do not tow unit on public roads. 

 

       12.  Do not carry passengers on unit. 

 

       13.  Avoid sudden turns or maneuvers. 

   

EXTENDED STORAGE PROCEDURES

 

1.  Wash and clean vacuum, and lubricate any lubrication points. 
2.  Drain fuel from the tank and run vacuum until fuel is exhausted in carburetor. 
3.  Drain and change the engine oil. 
4.  Clean tires and check pressure. Raising and supporting unit with weight off tires is recommended. 
5.  When storing a unit with Rubbermaid

 containers, leave containers latched to top. 

TRAC VAC WARRANTY POLICY 

 
 
Midwest Equipment Manufacturing, Inc. will repair or replace, free of charge, any part, or parts 
that are defective in material or workmanship or both for a period of one year residential use, and 
90 day’s for commercial and rental use.  The purchaser will pay transportation charges on parts 
submitted for replacement under warranty.  For warranty service, contact your local dealer from 
whom the unit was purchased.  There are no other express or implied warranties.  Some states do 
not allow limitations on how long an implied warranty lasts, and some states do not allow the 
exclusion or limitation of incidental or consequential damages, so the above limitation and 
exclusion may not apply to you.  This warranty gives you specific legal rights and you may also 
have other rights, which vary from state to state. 

 
 

MIDWEST EQUIPMENT MANUFACTURING, INC. 

5225 Serum Plant Rd. 

Thorntown, IN 46071 

Phone: 1-800-Trac-Vac 

Web Page: 

www.trac-vac.com

  E-Mail: 

[email protected]

 

Summary of Contents for 682-H












Reviews: