TQ-Systems TQMa6x, User Manual

Page: 46 / 58

User's Manual l TQMa6x & TQMa6xP UM 0403 l © 2019, TQ-Systems GmbH Page 40
3.3.4 Pinout connector X3
Table 52: Pinout connector X3
Ball I/O Level Group Signal Pin Signal Group Level I/O Ball
– P 0 V POWER DGND 1 2 DGND POWER 0 V P –
F4 I
–
28
MIPI-CSI CSI_CLK0_N 3 4 MLB_C_N MLB
–
28
O A11
F3 I –
28
MIPI-CSI CSI_CLK0_P 5 6 MLB_C_P MLB –
28
O B11
– P 0 V POWER DGND 7 8 DGND POWER 0 V P –
E4 I –
28
MIPI-CSI CSI_D0_N 9 10 MLB_D_N MLB –
28
I/O B10
E3 I
–
28
MIPI-CSI CSI_D0_P 11 12 MLB_D_P MLB
–
28
I/O A10
– P 0 V POWER DGND 13 14 DGND POWER 0 V P –
D1 I
–
28
MIPI-CSI CSI_D1_N 15 16 MLB_S_N MLB
–
28
I/O A9
D2 I
–
28
MIPI-CSI CSI_D1_P 17 18 MLB_S_P MLB
–
28
I/O B9
– P 0 V POWER DGND 19 20 DGND POWER 0 V P –
E1 I
–
28
MIPI-CSI CSI_D2_N 21 22 DSI_CLK0_N MIPI-DSI
–
28
O H3
E2 I –
28
MIPI-CSI CSI_D2_P 23 24 DSI_CLK0_P MIPI-DSI –
28
O H4
– P 0 V POWER DGND 25 26 DGND POWER 0 V P –
F2 I –
28
MIPI-CSI CSI_D3_N 27 28 DSI_D0_N MIPI-DSI –
28
O G2
F1 I
–
28
MIPI-CSI CSI_D3_P 29 30 DSI_D0_P MIPI-DSI
–
28
O G1
– P 0 V POWER DGND 31 32 DGND POWER 0 V P –
C5 O 2.5 V XTAL CLK2_N 33 34 DSI_D1_N MIPI-DSI –
28
I H2
D5 O 2.5 V XTAL CLK2_P 35 36 DSI_D1_P MIPI-DSI
–
28
I H1
– P 0 V POWER DGND 37 38 DGND POWER 0 V P –
E11 I
3.0 V
29
CONFIG TAMPER 39 40 SPI-NOR_WP# CONFIG 3.3 V I –
3.3.5 Pinout differences connector X2, TQMa6x Rev. 02xx / Rev. 04xx
The following table shows the pinout differences at connector X2 between TQMa6x revision 02xx and TQMa6x revision 04xx:
Table 53: Pinout differences TQMa6x revision 02xx and TQMa6x revision 04xx
Module Pin Signal Group Level I/O
TQMa6x revision 02xx
X2-18 VCC8V25_OTP 30 CONFIG 8.25 V P
X2-20 VCC3V3_OTP 30 CONFIG 3.3 V P
X2-22 OTP_SCL
30
CONFIG 3.3 V I
X2-24 OTP_SDA
30
CONFIG 3.3 V I/O
TQMa6x revision 04xx
X2-18 TQM_PWR_OFF# CONFIG 5 V I
X2-20 DNC – – –
X2-22 DNC – – –
X2-24 DNC – – –
28: See i.MX6 Data Sheets (1), (2), and (3).
29: Use VSNVS_REF_OUT as reference voltage.
30: Only for production. Do not connect.