manualshive.com logo in svg

TPS proCHEM-S, Manual, Page: 8 / 36

Share
Download
TPS proCHEM-S Manual Download Page 8

 

Page 8

2.  Operating Modes 

The function switch is used to select the required mode. The four 
operating modes available are… 

1. 

Set Upper Limit

 

: Switch to 

Set Upper Limit 

when setting the 

Salinity/TDS value at which the High LED and 
relay output are activated. The relay output is 
not operational in this mode.  

Factory-set to activate when the reading is 

above

 the Upper Limit. Can be user set to be a 

activate when the reading is 

below

 the Upper 

Limit. See section 3.5. 

2. 

Set Lower Limit

 

: Switch to 

Set Lower Limit 

when setting the 

Salinity/TDS value at which the Low LED and 
relay output are activated. The relay output is 
not operational in this mode. 

Factory-set to activate when the reading is 

below

 the Lower Limit. Can be user set to be a 

activate when the reading is 

above

 the Lower 

Limit. See section 3.5. 

3. 

Calibrate

 

: Switch to Calibrate mode to place the 

pro

CHEM

-S

 into standby (eg. when 

calibrating). This mode disables the two output 
relays to avoid chemicals being added when 
placing the sensor into calibration buffers. 

4. 

Automatic Control

  : Switch  to 

Automatic Control 

to enable the 

Alarm LED’s and relay outputs. These will be 
activated when the Salinity/TDS is outside the 
Upper and Lower limit values. See section 3.5. 

 

Summary of Contents for proCHEM-S





































Reviews:

No comments