manualshive.com logo in svg

Toyota HILUX 'A' DECK, Fitting Instructions Manual

Share
Download
Toyota HILUX 'A' DECK Fitting Instructions Manual Download Page 27

Page 27 of 34

Accessory Part No. PZQ70-89870

ISSUE 4: 09/10/18

Hard Tonneau Cover, A-Deck
Accessory Part No. PZQ70-89870  

TC0403c

66. Connect the 6-way male connector (1) to mating female connector (2) located in the front/LH Tonneau area.
Using a 7x12 cable tie clip (3), fasten the female harness to the bracket (4). 

See Dia #66.

Diagram #66

67.

3

4

2

1

Important

Open and close the Tonneau lid to confirm the
harness does not snag in the hinge operation of the
Tonneau lid.

Important

• Reconnect the negative battery terminal.

Battery Post terminal to be torqued in between 2.9
and 7.8Nm.

• Check the operation of the Tonneau cover ajar feedback system:
          o Ensure the car is unlocked.
          o Open the Tonneau cover window.
          o Check that the door ajar indicator on the instrument cluster is “on”.
          o Close the Tonneau cover.
          o Check the door ajar indicator on the instrument cluster is “off”.

For Locking Tonneau Cover Variants:

• Check the operation of the Locking system:
         o Lock the car and check that the Tonneau Cover is locked.
         o Unlock the car and check that Tonneau Cover is unlocked.

Summary of Contents for HILUX 'A' DECK

































Reviews:

No comments

Brands by name

Popular brands

Load more brands