Toyota HILUX 'A' DECK Fitting Instructions Manual Download Page 1

Page 1 of 34  

Place these instructions in vehicle’s glove box after installation is complete

Accessory Part No. PZQ70-89870

Installation Time: Approx. 4h 15min

Clean Tonneau Cover
with a mild detergent and 
water solution.

Do not use abrasive 
cleaners or solvents.

Care Instructions:

IMPORTANT!

Please check content of kit using this list and subsequent sketches.  Advise discrepancies to TMCA at once. 

Do not stand/sit or rest heavy objects on Tonneau Cover.

Do not carry open volatile chemicals with Tonneau Cover installed.

Humans or animals are not to be under the closed Tonneau Cover at any time.

Securely lock Tonneau Cover before operating vehicle.
Tonneau Cover is not dust or water tight.

If contact with volatile chemicals occurs clean Tonneau Cover with mild detergent and water solution. 

PARTS, SERVICE & ACCESSORIES

MAINTENANCE

If lubrication of the locks or hinges is required use only Graphite Powder. 
DO NOT use any other lubricants or oils.

HILUX ‘A’ DECK

(With Sports Bar)

September, 2016 Production Onwards

HARD TONNEAU COVER FITTING INSTRUCTIONS

TC0403c

Accessory Part No. PZQ70-89870

ISSUE 4: 09/10/18

- Check that all work practices comply with safety standards.

- Please wear appropriate clothing and use safety equipment.

Safety Notes

-

-

-

-

-

-

Read through the fitting instructions before installation of accessory.

Always install the accessory following the fitting instructions. Failure to do so may cause damage to the vehicle or 
the accessory.

Ensure all recyclable discarded vehicle accessory components and packaging are recycled following local 
recycling regulations.

It is always recommended that this accessory is fitted by a qualified Toyota Technician.

Safely store and protect any removed vehicle components.

Ensure all bare metal surfaces are protected using Automotive Bare Metal Primer and touch-up paint.

Remove all metal swarf and dust from all vehicle surfaces if surface is used for accessory installation.

General Notes

Summary of Contents for HILUX 'A' DECK

































Reviews: