TOX PRESSOTECHNIK TOX-FinePress PFL 002 Original Operating Instructions Download

Page: 29 / 72

Installation

TOX_Manual_FinePress_PFS-PFL-PFW_en

6 Installation

6.1

Safety during installation

The installation may only be carried out by trained and authorized service
personnel.

DANGER

Electrical hazards in case of contact with live parts!

Electric shock, burns or death in case of contact with live parts!

Have all work on the electrical equipment performed by an electrician.

Disconnect power supply.

Wait for residual energy to disspate safely (at least 3 minutes).

WARNING

Ejecting parts and compressed air from compressed air conducting
lines!

Serious injuries to eyes and body cavities!

Always connect and disconnect lines without pressure.

Pay attention to maximum permitted pressures.

Wear individual protective equipment.

WARNING

Hazard from suspended loads!

Severe crushing, impacts and serious accidents as a result of improper
transportation and falling load!

Only use lifting gear that is appropriate and in perfect technical condi-
tion, as well as load attachment devices with an adequate safe working
load.

Never stand or work under suspended loads.

Make sure that that no person is in the danger area.

When transporting and setting down, make sure that no parts of the
body become jammed.

Wear suitable personal protective equipment (e.g. safety boots).

Summary of Contents for TOX-FinePress PFL 002









































































Search results

Summary of Contents for TOX-FinePress PFL 002

Reviews:

Related manuals for TOX-FinePress PFL 002

Brands by name

Popular brands

TOX PRESSOTECHNIK TOX-FinePress PFL 002, Original Operating Instructions

Search results

Summary of Contents for TOX-FinePress PFL 002

Reviews:

Related manuals for TOX-FinePress PFL 002

Brands by name

Popular brands