Town & Country Fireplaces TC36.NG03C Instructions Manual Download Page 12

TC36.NG03C 290411-20

12

WARNING

This conversion kit 
shall be installed by  a 
qualifi ed service agency 
in accordance with the 
manufacturer's instructions 
and all applicable codes and 
requirements of the authority 
having jurisdiction. 

If the information in these 
instructions is not followed 
exactly, a fi re, explosion 
or production of carbon 
monoxide may result 
causing property damage, 
personal injury or loss of 
life. 

The qualifi ed service agency 
is responsible for the proper 
installation of this kit. The 
installation is not proper and 
complete until the operation 
of the converted appliance is 
checked as specifi ed in the 
manufacturer's instructions 
supplied with the kit

.

If the unit is to be used on propane 
convert as follows using the 
components supplied with this 
fi replace:

CAUTION

The gas supply and electrical power 
shall be shut off before proceeding 
with the conversion.

Note: 
Factory supplied components must be used 
to ensure correct input.  After conversion 
confi rm proper manifold pressure.

1.  Ensure the burner, pilot and gas 
 

supply are turned off, and the 

 

appliance has cooled.

2.  Using a 1/2” wrench, undo the natural gas 

burner orifi ce, (marked 

#30

). (Fig. #19)

3.  Apply a small amount of pipe joint com-

pound to the threads of the propane 
burner orifi ce (marked #

45

) to ensure 

a good seal, before screwing it into the 
fi tting.

4.  Open primary air shutter fully.

5.    With a 7/16” wrench loosen the pilot head 

on the pilot assembly (Fig. #20)

Fig #19

Fig #20

Propane Conversion

MAIN BURNER 
(#45) ORIFICE  (5021.34)

MINIMUM RATE SCREW (5005.015)

CONVERSION LABEL (5052.5208)

Summary of Contents for TC36.NG03C





















Reviews: