background image

WARRANTY

Tower Hobbies

®

guarantees this kit to be free from defects in both material and workmanship at the date of purchase. This warranty

does not cover any component parts damaged by use or modification. In no case shall Tower Hobbies' liability exceed the original
cost of the purchased kit. Further, Tower Hobbies reserves the right to change or modify this warranty without notice.

In that Tower Hobbies has no control over the final assembly or material used for final assembly, no liability shall be assumed nor

accepted for any damage resulting from the use by the user of the final user-assembled product. By the act of using the 
user-assembled product, the user accepts all resulting liability.

If the buyers are not prepared to accept the liability associated with the use of this product, they are advised to return this kit

immediately in new and unused condition to the place of purchase.

ASSEMBLY INSTRUCTIONS

WINGSPAN: 60 IN.
LENGTH: 50 IN.
WING AREA: 660 SQ. IN.
WEIGHT: 5.5 LBS.
WING LOADING: 19.2 OZ./SQ. FT.

© Copyright 2000  V1.0

ALMOST READY-TO-FLY RADIO CONTROLLED MODEL AIRPLANE

TOWZ1149 for TOWA1100

Summary of Contents for Tower Trainer 40 ARF

























Reviews: