background image

5

ENGLISH

INSTALLATION PROCEDURE

IMPORTANT!

  Before installation, any dirt and debris in the cold/hot water supply pipes must be washed out.

1)  Wipe off any dirt around the installation 

hole. 

2)  Measure the installation hole, then select a 

gasket that matches the hole diameter from 
the 2 kinds provided.

    N OTE: If the wrong gasket is used, water 

may leak under the counter.

Installing the Spout

Hole over ø 
1-7/16” (36mm) 

Hole under ø 
1-7/16” (36mm)

Flat Gasket

Winged Gasket

Spout

Spout Mounting 

Shaft

Installation Hole

Connection Pipe

Spout Bottom

Gasket

Spout 

Mounting 

Nut

Lock 

Washer 

(big)

Flat 

Washer (big)

Spout 

Mounting 

Flange

Spout 

Mounting 

Shaft

Spout

Mounting 

Shaft

Spout

Shank Body

Flat Washer (small)

Lock Washer (small)

Spout 

Mounting Nut

 

 

Installing the Valve Assemblies

1)  Wipe off any dirt around the installation hole. 

2)  Place the deck sealing gasket (white) around 

both hoses of one valve assembly and move it 
to the top, stopping just below the cartridge 
and nut.  Place hoses through the mount-
ing hole and allow the valve to rest on the 
surface.

    C AUTION: The valve body assembly (la-

beled C) of the cold water supply must be 
installed on the right side of the spout, the 
valve body assembly (labeled H) of the hot 
water supply must be installed on the left 
side. 

3)  From below the mounting surface, place gas-

ket (black) around both hoses followed by slip 
washer and fastening nut.  Thread nut onto 
valve body until valve unit is secure.

4)  Repeat step 3 for the other valve assembly.

    C AUTION: When placing the connecting 

hose through the fastening nut, make the 
cap nut go through the escape hole.

Cold Water Supply 

Valve Body Assembly

Gasket (white)

Counter

Gasket (black)

Slip Washer

Fastening 

Nut

Connecting 

Hose

Cap Nut

C Label

Cold Water 

Supply Hose

Top

Relief hole for 
hose passage

Bottom

3)  Place the gasket around both the connection pipe and mounting shaft, 

and move it up against the bottom surface of the faucet body. Place it 
into the mounting hole until the spout rests on the surface.

    C AUTION: Be careful not to scratch or contaminate the o-ring. Other-

wise, water leakage may occur.

4)  Place the mounting flange onto the shaft of the faucet as shown to the 

right.  Place the flat washer and lock washer onto the shaft and fasten 
the nut until snug.  Double-check faucet alignment and tighten nut to 
secure.

5)  Press shank body onto connection pipe until it is fully seated.  Place flat 

washer and lock washer onto bottom of connection pipe and fasten nut 
tightly to secure.

Summary of Contents for Renesse TL170DD

























Reviews: