background image

FUEL & OIL MIXTURE 

Never fill the fuel tank to the very top.
Never add fuel to the tank in a closed non-ventilated area.
Do not add fuel to this unit close to an open fire or sparks.
Be sure to wipe off spilled fuel before attempting to start engine.
Do not attempt to refuel a hot engine.

Fuel used for this model is a mixture of unleaded gasoline and approved engine
lubricant. When mixing gasoline with two-cycle engine oil, use only gasoline which
contains NO ETHANOL or METHANOL(Types of Alcohol) Use Branded 89 octane
or higher
Unleaded gasoline known to be of good quality. This will help to avoid possible
damage to engine fuel lines and other engine parts. 

MIXTURE RATIO IS 40:1

GASOLINE-25PART

OIL-1 PART

Fuel mixture at the rate other than 40:1 may
cause

damage

to

the

engine,

Ensure

mixture ratio is correct. 

FUEL

IMPORTANT

The engine uses two-stroke fuel, a mixture

Two-stroke fuel may separate. Shake fuel

of gasoline and 2-stroke lubricant 40:1

container thoroughly before each use. Stored

fuel ages. Do not mix more fuel than you 
expect to use within a month.

GASOLINE

Use branded 89 octane or higher unleaded
gasoline known to be of good quality.

FUEL AND OIL MIXTURE

STORING FUEL

Store fuel only in a clean, safe, approved

Inspect fuel tank making sure that it is

container. Check and follow local

clean and fill with fresh fuel. Use a mixture

ordinances. on type and location of

of

40:1

storage container.

Summary of Contents for TP445441





























Reviews: