background image

Do not contact the generator to a commercial power line. Connection to a commercial

power line may short circuit the generator and ruin it or cause electric shock hazard. 

Use the transfer switch for connecting to domestic circuit.

WARNING

Engine becomes extremely hot during and for some time after operation. 

Keep combustible materials well away from generator area.

Be very careful not to touch any parts of the hot engine especially the muffler area

or serious burns may result.

WARNING

No smoking while handling the battery. The battery emits flammable hydrogen gas,

which can explode if exposed to electric arcing or open flame.

Keep the area well-ventilated and keep open flames/sparks away when handling the battery.

WARNING

Do not operate in rain, in wet or damp conditions, or with wet hands.

The operator may suffer severe electric shock if the generator is wet due to rain or snow.

WARNING

Keep children and all bystanders at a safe distance from work areas.

WARNING

If wet, wipe and dry it well before starting. Do not pour water directly over the generator, nor wash it

with water.

WARNING

Be extremely careful that all necessary electrical grounding procedures are followed during each and

every use. Failure to do so can be fatal.

WARNING

It is absolutely essential that you know the safe and proper use of the power tool or appliance that

you intend to use. All operators must read, understand and follow the tool/appliance owners manual.

Tool and appliance applications and limitations must be understood. Follow all directions given on

labels and warnings. Keep all instruction manuals and literature in a safe place for future reference.

WARNING

Use only "LISTED" extension cords.

When a tool or appliance is used outdoors, use only extension cords marked "For Outdoor Use".

Extension cords, when not in use should be stored in a dry and well ventilated area.

WARNING

Always switch off generator's AC circuit breaker and disconnect tools or appliances when not in use,

before servicing, adjusting, or installing accessories and attachments.

WARNING

CAUTION

Make sure the engine is stopped before starting any maintenance, servicing or repair.
Make sure maintenance and repair of the generator set are performed by properly trained personnel only.

4

Summary of Contents for TP155001























































Reviews: