background image

STEP • 18

STEP • 19

09

© Sheds (Midlands) Limited 2021

www.totalsheds.co.uk

SECURE THE SHELVING 

SECTIONS IN PLACE  

(If 6ft, 10ft, 14ft or 18ft 

Start with the 2ft Shelf 

Section).

18a.

 Insert the shelf assembly into the 

correct section of the shed interior. 

18b.

 Use 4.0 x 70mm screws to secure 

the shelving panels in place. Use 4 

screws per shelf panel to ensure that 

the section is properly secured. 

18c. 

Repeat this for all shelving 

sections. For the 6ft, 10ft, 14ft and 18ft 

Builds, the 2ft section will always be 

first. 

SECURING THE SHELVES

= Drill Points using

screws provided as shown

x2

4.0 x 70mm

 

Per Floor Section

x3

x4

4.0 x 70mm

Per Shelf Panel

x2

4.0 x 70mm

 

Per Floor Section

x3

x1

4.0 x 38mm

DIAMOND CAPS

DIAMOND CAPS

Add the Finishing 

Touch. (Optional)

Timber is a naturally grown product and may shrink and warp when dried out, timber is a porous 

material which can absorb water. Although all of our buildings come pressure treated we strongly 

advise the building is re-treated with an oil/spirit based treatment inside and out to make the timber 

water repellent and to preserve the quality and life of the product.

Congratulations

 

Total Sheds

28 Charles Street, 

Willenhall, WV13 1HG

Tel: 01902 636 529 

Email: [email protected]

 

Per Diamond

Summary of Contents for Pent Potting Shed













Reviews: