Tosot GPC05AP-A3NNA1A User Manual Download Page 27

Page: 27 / 30

Troubleshooting

Whether the unit is
restarted up after
stopping immediately?

Is plug loose?
Power failure?
Is the power too low?
Whether the air filter

is too dirty?
Whether the set

temperature is proper?
Whether door and

window are closed?
Whether the unit is

interfered seriously

(such as static pressure,

unstable voltage)?

Whether remote control

is within the receiving

range?
Whether it's blocked

by obstacles?

Is sensitivity of remote

control low?

Whether there's a flu-

orescence lamp in the

room?

The unit is experiencing the

3-Minute Compressor Protection.

Wait for 3min, and then turn on

the unit again. For a detailed

explanation, please refer to

the answers below the diagram.
Reinsert the plug.
Wait after power recovery.
Wait after voltage is resumed.

Clean the air filter.

Adjust the temperature.

Close door and window.

Please pull out the plug. Insert

the plug after about 3min, and

then turn on the unit.

The receiving range of remote

control is 25 feet. Do not exceed

this range.

Remove the obstacles.

Check the batteries of the remote

control. If the power is low, please

replace the batteries.

Move the remote control close

to the air conditioner.

Air conditioner

can't operate

Poor cooling

Air conditioner can't

receive signals from

remote control or

remote control is

not sensible.

Issues

Self check

Possible solutions

Summary of Contents for GPC05AP-A3NNA1A































Search results

Summary of Contents for GPC05AP-A3NNA1A

Reviews:

Related manuals for GPC05AP-A3NNA1A

Brands by name

Popular brands

Tosot GPC05AP-A3NNA1A, User Manual

Search results

Summary of Contents for GPC05AP-A3NNA1A

Reviews:

Related manuals for GPC05AP-A3NNA1A

Brands by name

Popular brands