Toshiba TF 461 Instruction Manual Download

Page: 60 / 91

Your TF 461 as a printer

TF 461

TOSHIBA

Your TF 461 as a printer

System requirements

Connect your TF 461 to a computer which
meets the following system requirements:

CPU:

• i80386SX (or higher)

RAM:

• min. 4 MB

Hard disk space:

• min. 5 MB free space

Software:

•

MS-DOS version 5.0

or higher;

•

Microsoft Windows

version 3.0/3.1

or higher (in extended -386 enhanced-
mode)

•

Microsoft Windows 95

• IBM OS/2 1.3/2.0 or higher

If you would like additional information for
installing the printer drivers, you can read
or print out the README.TXT file. After
the printer driver has been installed, this
file can be found in the directory
\PRTCIJP.

Connecting the fax
machine to the
computer

The TF 461 has an 8-bit Centronics
parallel interface. Perform the following
steps to connect the TF 461 to your
computer:

1. Disconnect the TF 461 from the main

supply.

2. Switch your computer off.

3. Connect a parallel cable to the

corresponding socket on the rear of hte
TF461.

Parallel printer cable not supplied.

4. Secure the connector on the parallel cable

by means of the wire clips.

5. Connect the other and of the parallel cable

to a spare parallel port on your PC.

Parallel cables should be no longer
then 2 meters.

Summary of Contents for TF 461




























































































Search results

Summary of Contents for TF 461

Reviews:

Related manuals for TF 461

Brands by name

Popular brands

Toshiba TF 461, Instruction Manual

Search results

Summary of Contents for TF 461

Reviews:

Related manuals for TF 461

Brands by name

Popular brands